|
09-08-2010
|
#1 |
Join Date: Apr 2008
Location: Gainesville GA
Posts: 231
|
PCV F-tube home-brew?
I am in the middle of replacing injectors, coils, wires, etc; and when I go to replace the PCV valves I noticed that the F-tube is split. I know white racing has a replacement but I thought I remember someone has posted a home-brew with pictures and parts needed. I have searched without success. Can some help a brother
 ? Thanks.
__________________
1991 ZR1, White/Red. |
|
|
|
09-08-2010
|
#2 |
Join Date: May 2005
Location: Leesburg, VA
Posts: 2,713
|
Re: PCV F-tube home-brew?
FWIW, Samco makes the PCV tubes now (except the elbows at the IH, which are still available from GM and fairly cheap). I think the Samco's are similar in price to the inflated price of the NLA GM stuff.
__________________
Bob Saveland Former owner of #2517 [IMG]http://a.random-image.net/aurora40/vette.jpg[/img] |
|
|
|
|
09-08-2010
|
#3 |
 
Join Date: Jul 2007
Location: Bartlett, IL
Posts: 7,169
|
Re: PCV F-tube home-brew?
I think LGAFF did it.. but I cannot seem to find the post
__________________
1990 Corvette ZR-1 #1051 Watson Headers (2" Primary) - Flowmaster Cats - Borla Catback Late Model IH - Plenum Coilovers - 4.10s Custom Interior NCM Lifetime Member #978 |
|
|
|
09-09-2010
|
#4 |
 
Join Date: Nov 2006
Location: DeBary , Fl.
Posts: 119
|
Re: PCV F-tube home-brew?
I ran factory PCV valves from I/H to a "F" plastic connector (behind engine) back to throttle body using all braided hose 3/8 or AN6. Works & looks fine! Dorman has the rubber elbow fittings for the I/H (at most HELP trays in parts stores)
__________________
Gene in Fl. :handshak: ______________ 95 ZR-1 #399 Dunn heads X-pipe w/3" misc. mods |
|
|
|
|
09-09-2010
|
#5 | |
|
Join Date: Apr 2008
Location: Gainesville GA
Posts: 231
|
Re: PCV F-tube home-brew?
Quote:
__________________
1991 ZR1, White/Red. |
|
|
|
|
|
09-09-2010
|
#6 |
|
Join Date: Nov 2006
Location: DeBary , Fl.
Posts: 119
|
Re: PCV F-tube home-brew?
Had 1 in my tool box but you can find 1 at parts or hardware (any 3/8 "F Y or T" will work to tie all 3 together while running 1 back to T/B. Those orig. parts are costly, you could sell yours if you like this setup!
__________________
Gene in Fl. :handshak: ______________ 95 ZR-1 #399 Dunn heads X-pipe w/3" misc. mods |
|
|
|
|
09-09-2010
|
#7 |
|
Join Date: Apr 2008
Location: Gainesville GA
Posts: 231
|
Re: PCV F-tube home-brew?
Dynomite: Sorry for the confusion. I am looking for a inexpensive replacement for the tube/hose that the PCV valves sit in as mine has split open
 and $170.00 for a replacement seems steep. So I have seen somewhere that one could fabricate a replacement and that is what I am looking for. Belsy: Thanks for the info. I will check the parts store this evening for the needed pieces.
__________________
1991 ZR1, White/Red. |
|
|
|
 |
|
|
Linear Mode
