ZR-1 Net Registry Forums  

Go Back   ZR-1 Net Registry Forums > C4 ZR-1 > C4 ZR-1 Technical Postings

Reply
 
Thread Tools Display Modes
Old 04-17-2010   #11
todesengel
 
Join Date: Apr 2010
Location: O'Fallon, Mo
Posts: 738
Default Re: Ok, I ordered my headers from ss

Just finished my order with them, thanks Jeff.

Do you think that I should go ahead and order new injectors for this thing as well? The guy that had it before me said that he did so, but I am not so sure of the work that was done. While it is all apart, I would prefer that it is all going to be right. Also the coils, do people just typically go with factory replacements?

Thanks
Quote:
Originally Posted by -=Jeff=- View Post
these cover, plenum to IH, Coolant tubes and Cam covers:

QTY 48 Metric 18-8 SS Socket Head Cap Screw M8 Thread, 55mm Length, 1.25mm Pitch, Packs of 10 (min quantity 5) 91292A156

QTY 8 Metric 18-8 SS Socket Head Cap Screw M6 Thread, 50mm Length, 1mm Pitch, Packs of 25 (min quantity 1) 91292A144

QTY 12 Metric 18-8 SS Socket Head Cap Screw M8 Thread, 25mm Length, 1.25mm Pitch, Packs of 25 (min quantity 1) 91292A148

QTY 6 Metric 18-8 SS Socket Head Cap Screw M6 Thread, 25mm Length, 1mm Pitch, Packs of 50 (min quantity 1) 91292A138

Also suggested:

Bolts for TB Cover and TB as well as Air Horn, Bolts for MAP Sensor and Throttle cable hold down
todesengel is offline   Reply With Quote
Old 04-17-2010   #12
jonszr1
 
jonszr1's Avatar
 
Join Date: Sep 2006
Location: lone pine and mammoth lakes
Posts: 1,407
Default Re: Ok, I ordered my headers from ss

most guys just use the factory coils, they are a good piece for our cars. on the injectors, you might test to see if they hold pressure, what kind did he use ?????
jonszr1 is offline   Reply With Quote
Old 04-17-2010   #13
todesengel
 
Join Date: Apr 2010
Location: O'Fallon, Mo
Posts: 738
Default Re: Ok, I ordered my headers from ss

Quote:
Originally Posted by jonszr1 View Post
most guys just use the factory coils, they are a good piece for our cars. on the injectors, you might test to see if they hold pressure, what kind did he use ?????
Ok, going through some of the paperwork from the previous owner, I found the receipt for the injectors he ordered in 1997 for it. Just looking for feedback on the injector types, and whether I should replace these with brand new lucas disk type (I have always had great luck v. single pintle)

Injectors were purchased new from five0motorsports.com on 6/20/97

8 bosch 0280150561/556 (11140,11122, zr1-11115) Brand new secondary set

8 bosch 0280150561/556 (zr1-11113) Brand new primary set
todesengel is offline   Reply With Quote
Old 04-17-2010   #14
Pete
 
Pete's Avatar
 
Join Date: Dec 2003
Location: Chicagoland,IL
Posts: 2,679
Default Re: Ok, I ordered my headers from ss

You can buy the Lucas injectors,should be fine.
If you have a 1990-1992 ZR-1 the primary and secondary Injectors have some small difference.
The secondaries look just like any other injector i.e.like LT1 injectors the primaries seal on the body of the injector the O-ring sits in the intake/Injector Housing also the key way for the electrical plug is offset on the primary injectors where as the secondary injector key way is in the middle just file down the keyway for the primary injectors.
You will understand it better when you take her apart.

1993-1995 injectors are same just keyway difference.

Pete
__________________
'91 #1635 PoloGreen 350 LT5
11.09 @ 129.27
11.04 @ 128.86
474RWHP 400RWTQ
http://www.youtube.com/watch?v=SFNFOhGGlR4
http://www.youtube.com/watch?v=ZlRIOMwaDYY
https://sites.google.com/site/peteszr1garage
Pete is offline   Reply With Quote
Old 04-18-2010   #15
Paul Workman
 
Paul Workman's Avatar
 
Join Date: Nov 2007
Location: Squires (near Ava MO in the Mark Twain N'tl Forest) - Missouri
Posts: 6,493
Default Re: Ok, I ordered my headers from ss

This is the little bracket I fabb'ed up for the dip stick. Woiks poifect!

(Sorry 'bout the focus on the top pic, but ya getz the I-dear, I'm sure.)




P.
__________________
Good carz, good food, good friendz = the best of timez!

90 #1202
"FBI" top end ported & relieved
Cam timing by "Pete the Greek"
Sans secondaries
Chip & dyno tuning by Haibeck Automotive
SW headers, X-pipe, MF muffs

Former Secretary, ZR-1 Net Registry
Paul Workman is offline   Reply With Quote
Old 04-18-2010   #16
ZZZZZR1
Banned
BANNED
 
Join Date: Oct 2006
Location: MD
Posts: 3,690
Default Re: Ok, I ordered my headers from ss

Quote:
Originally Posted by Paul Workman View Post
This is the little bracket I fabb'ed up for the dip stick. Woiks poifect!

(Sorry 'bout the focus on the top pic, but ya getz the I-dear, I'm sure.)




P.
Woah! Nice piece
ZZZZZR1 is offline   Reply With Quote
Reply


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 11:56 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright ZR-1 Net Registry 2020