Can I get a lift? - Page 6 - ZR-1 Net Registry Forums

ZR1Vette · 11-21-2009

Quote:

Originally Posted by LGAFF

Ok, now I am at the WTF do I do stage, 2Kpounds of metal in the driveway, directions are somewhere in the belly of this thing. There was a stray bolt sitting on the top.

Oh, and a nosey neighbor stopped and asked what it was, I told them it was my new steel reinforced bed.

The bolt..probably from on shipping pieces...the end metal brackets are bolted to the runners (metal decking) and they do come off on occasion. Start unpacking...you can remove the wrap, then most everything that is below and above the decking that is bolt to the end packing brackets. the columns weigh about 100 lbs each so you can move. Now...the decks are another story...one without the ram weighs in at 300 lbs and the one with the hydraulic ram weighs a little over 400 lbs. Unless you have some strong back weak minded gorillas suggest getting a engine hoist...works great...also some hoist straps (nylon type so you do not scratch the decks... strap a mid point and lift top deck slightly and then unbolt from packing brackets. Next do the lower deck.
This is a much better assembly guide than the one that comes with the lift>>
http://www.gregsmithequipment.com/Articles.asp?ID=331

Read over first to become familiar with the assembly process and if you have any questions just let me know and I can walk you thru...suggest you have two others help you with the assembly... Took Phil, Rich and me about 5 hrs to assemble (learning curve plus it was HOT so lots a recuperate time).

LGAFF · 11-21-2009

Former Illinois state deadlift record holder @ 730lbs....should be good, also bought forearm forklifts.......should be interesting

Ccmano · 11-21-2009

Sorry Lee, Not going to be able to get over there today. We have too much last minute packing and running around left to do. Hope you get enough help to get the thing done. Can't wait to see the pix of it up and running in your garage.
Good luck
H

LGAFF · 11-21-2009

No one showed, Got the post in and everything so far.....moving the 440lb ramp next.....should be exciting.

LGAFF · 11-21-2009

All the heavy $hits done, you guys can come over.....

Not fun as a one man job! Just me a floor jack!

Kb7tif · 11-21-2009

When there a will theres a way.. Trust me. You will get it.

phrogs · 11-21-2009

Quote:

Originally Posted by LGAFF

All the heavy $hits done, you guys can come over.....

Not fun as a one man job! Just me a floor jack!

you didn't blow a gasket did you?

-=Jeff=- · 11-21-2009

Hey lee, Who was suppose to come and help?

LGAFF · 11-21-2009

Pretty much an open invite......Hans had to pack..been there so no big deal......doing this solo is possible, but sucks.

Toyvet1 · 11-22-2009

Lee did you get it all assembled today. Leveled ? Where are the photos.

11-21-2009	#52
LGAFF Join Date: Mar 2007 Location: Crystal Lake, IL Posts: 7,194	Re: Can I get a lift? Former Illinois state deadlift record holder @ 730lbs....should be good, also bought forearm forklifts.......should be interesting __________________ LGAFF 90 #966-150K miles-sold 92 #234-sold 1987 Callaway TT #17 1991 ZR-1 #1359

11-21-2009	#53
Ccmano Join Date: Jun 2006 Location: Sparks, NV Posts: 2,852	Re: Can I get a lift? Sorry Lee, Not going to be able to get over there today. We have too much last minute packing and running around left to do. Hope you get enough help to get the thing done. Can't wait to see the pix of it up and running in your garage. Good luck H __________________ 90'ZR-1 #1461 Red/Black Ported Intake, Degreed Cams, OBX Headers & Exhaust, Fidanza FW, Secondary Delete, Custom tune, C6 GS Wheels. Sold 08 C6 Z51 Crystal Red Metallic Sold Vararam Intake, Tune, Sold 05 C6 Z51 Red/Black Sold 90'ZR-1 #1723 Black/Gray Sold but not forgotten 91' Z51 L98 White Vert. My First, you always remember your first. Sold.

11-21-2009	#54
LGAFF Join Date: Mar 2007 Location: Crystal Lake, IL Posts: 7,194	Re: Can I get a lift? No one showed, Got the post in and everything so far.....moving the 440lb ramp next.....should be exciting. __________________ LGAFF 90 #966-150K miles-sold 92 #234-sold 1987 Callaway TT #17 1991 ZR-1 #1359

11-21-2009	#55
LGAFF Join Date: Mar 2007 Location: Crystal Lake, IL Posts: 7,194	Re: Can I get a lift? All the heavy $hits done, you guys can come over..... Not fun as a one man job! Just me a floor jack! __________________ LGAFF 90 #966-150K miles-sold 92 #234-sold 1987 Callaway TT #17 1991 ZR-1 #1359

11-21-2009	#56
Kb7tif Join Date: May 2009 Location: S Nevada Posts: 352	Re: Can I get a lift? When there a will theres a way.. Trust me. You will get it. __________________ 1995 Convertible Supercharged Auto 1974 454 550hp (avatar car) On the blocks- -Scharger install ! 1992-Zr-1 Sold. Watson Headers Ported Plenum, Housings Random tech cats Fidanza Flywheel Chipped, Relocated Mat Woods 165 stat Borlas, Straights 1996 Lt4 Sold 1994 Lt1 Sold 2004 Z06 Sold AKA** Illenema

11-21-2009	#58
-=Jeff=- Join Date: Jul 2007 Location: Bartlett, IL Posts: 7,169	Re: Can I get a lift? Hey lee, Who was suppose to come and help? __________________ 1990 Corvette ZR-1 #1051 Watson Headers (2" Primary) - Flowmaster Cats - Borla Catback Late Model IH - Plenum Coilovers - 4.10s Custom Interior NCM Lifetime Member #978

11-21-2009	#59
LGAFF Join Date: Mar 2007 Location: Crystal Lake, IL Posts: 7,194	Re: Can I get a lift? Pretty much an open invite......Hans had to pack..been there so no big deal......doing this solo is possible, but sucks. __________________ LGAFF 90 #966-150K miles-sold 92 #234-sold 1987 Callaway TT #17 1991 ZR-1 #1359

11-22-2009	#60
Toyvet1 Join Date: Dec 2007 Location: Bloomingdale, Il Posts: 330	Re: Can I get a lift? Lee did you get it all assembled today. Leveled ? Where are the photos.