Rear View Camera Install

[XfireZ51]

Originally Posted by WVZR-1

Now you've got the connector you need to work with unless you also put your hands on the C209 and it was easier to manipulate.

Were it here I might choose the 8 pin mating for the C209 because it might be easier to unlatch, remove the wire, crimp a new terminal with a pigtail to use for the RVC. The terminals are an easy source for me.

The first image I posted way back isn't in the '92 and earlier FSM because the CDM is right there also and they couldn't image that area as easily under the dash. Get the CDM out of the way and it should be much easier and maybe resemble the later image I posted back there.

Dave,

This blue connector is clearly a 10 cavity connector. I think I can get to this one to repin. Once I unlatch it, the IP side should move freely. I have some pins, not sure which one this is yet.

[WVZR-1]

Originally Posted by XfireZ51

Dave,

This blue connector is clearly a 10 cavity connector. I think I can get to this one to repin. Once I unlatch it, the IP side should move freely. I have some pins, not sure which one this is yet.

I'd think if you're using the C239 "BLU" they would be Metri-Pack 150 - in this link there's male & female ID's - I'd think easily sourced close locally!!

https://www.waytekwire.com/manf/45/D...FYWEswodIDUCJQ

If there's a GM dealer close see the shop foreman if the parts guy can't help you.

TRAY 2 - DELPHI TERMINAL SHOP & there's maybe another in TRAY 5

[XfireZ51]

Originally Posted by WVZR-1

I'd think if you're using the C239 "BLU" they would be Metri-Pack 150 - in this link there's male & female ID's - I'd think easily sourced close locally!!

https://www.waytekwire.com/manf/45/D...FYWEswodIDUCJQ

If there's a GM dealer close see the shop foreman if the parts guy can't help you.

TRAY 2 - DELPHI TERMINAL SHOP & there's maybe another in TRAY 5

Thanks Dave. I think I may actually have some of these already.

[chriskinzel]

I may not understand what is going on here. This camera might be Bluetooth. If not, when I did my backup camera I ran a wire with the camera cable to the radio. I connected to the backup lights for my input. Since I was already running 1 cable might as well as 1 more wire.

Chris

[ghlkal]

Originally Posted by XfireZ51

In the process of installing an appradio4 and including backup camera w it.

Which backup camera are you using?

Will you share the camera's installation when you are finished? Thanks

[XfireZ51]

Ok all. Finished the install of the rearview camera yesterday. Power and ground taken off backup lamps. Also attaches pic of the "elusive" reverse signal. Repinned it to take signal for appradio4. Works! I have run the camera cable down the left side of the car under sill plate and across the drivers side to the appradio4.

[XfireZ51]

I'm using an Audiovox camera.

[WARP TEN]

Originally Posted by XfireZ51

I'm using an Audiovox camera.

Hi Dom--Do you have to cut a hole in your license plate for that? --Bob

[XfireZ51]

Originally Posted by WARP TEN

Hi Dom--Do you have to cut a hole in your license plate for that? --Bob

Bob,

No. The camera sits flush w the face of the rear fascia, is pretty small and is pretty much out of sight. I'll install the License plate and post pics. Pretty neat. The Pioneer will add guidelines to the image, altho the image is reversed.

[XfireZ51]

Here's what it looks like w the plate on.