fuel injectors - Page 2 - ZR-1 Net Registry Forums

ROGER E · 06-11-2007

Uh oh. Please don't tell me I installed the wrong ones. I got the part number from posting in this thread:

http://zr1netregistry.com/forum/show...ghlight=150821

To make matters worse my engine is a 91 with 94 heads. It runs great but if there's room for improvment please do tell!

mrzzzr1 · 06-11-2007

Kurt White "White Racing" states R/C injectors are as good as it gets. I got mine for $68 each from R/C direct in Ca. Had to buy 8 primary o-ring seals that were not included and they were very pricey through a Buick Dealer my mechanic deals with. I suggest looking elsewhere for the seals.

swaindm · 06-12-2007

150821 is correct! I was confusing some non stock applications. Sorry!!

DMS

ROGER E · 06-13-2007

Quote:

Originally Posted by swaindm

150821 is correct! I was confusing some non stock applications. Sorry!!

DMS

Cool!

ffvetteman · 06-16-2007

Whew you guys got me nervous for a minute there!!! I got 16 150121's sitting on the table in front of me ready to go in.

This week I hope

Just need to get a hold of a set of spark plug wires now.

george henry · 07-14-2007

Hello. Just replaced all 16 injectors with Accel part number 150121 from Atlantic Speed for about $500. This took care of my high idle problem as well as a bad lack of power (bad stumble when the secondaries kick in), also replaced the PCV hose with the unit from White Racing and got new PCV valves. The old hose was a loose fit to the valves and this probably contributed to the high idle (1200 rpm), it now goes right to 750 rpm after start. The injectors were the originals and ethanol had taken its toll on them. I was a first timer on the plenum removal, it's not that big of a deal.
1990 #1507

george henry · 07-14-2007

Hello. Just replaced all 16 injectors with Accel part number 150121 from Atlantic Speed for about $500. This took care of my high idle problem as well as a bad lack of power (bad stumble when the secondaries kick in), also replaced the PCV hose with the unit from White Racing and got new PCV valves. The old hose was a loose fit to the valves and this probably contributed to the high idle (1200 rpm), it now goes right to 750 rpm after start. The injectors were the originals and ethanol had taken its toll on them. I was a first timer on the plenum removal, it's not that big of a deal.
1990 #1507

zr-1assassin · 07-15-2007

Quote:

Originally Posted by ffvetteman

Whew you guys got me nervous for a minute there!!! I got 16 150121's sitting on the table in front of me ready to go in.

This week I hope

Just need to get a hold of a set of spark plug wires now.

there is a new set on ebay with both pcv's!

george henry · 07-15-2007

Just read Roger E's post about using the outer slot on the injector for the clip to the fuel rail (the slot next to the o-ring?) I just pushed them into the rail and used the slots that look like they were made for the clip. There were no leaks and it runs fine. Does anybody know how much difference this makes? Should I worry?

Jagdpanzer · 07-15-2007

So do the Accel 150121 injectors work in both the 375 and 405 hp LT5 engines?

06-11-2007	#11
ROGER E Join Date: Apr 2004 Location: Folsom Posts: 23	Re: fuel injectors Uh oh. Please don't tell me I installed the wrong ones. I got the part number from posting in this thread: http://zr1netregistry.com/forum/show...ghlight=150821 To make matters worse my engine is a 91 with 94 heads. It runs great but if there's room for improvment please do tell!

06-11-2007	#12
mrzzzr1 Join Date: Jun 2004 Location: Mi Posts: 57	Re: fuel injectors Kurt White "White Racing" states R/C injectors are as good as it gets. I got mine for $68 each from R/C direct in Ca. Had to buy 8 primary o-ring seals that were not included and they were very pricey through a Buick Dealer my mechanic deals with. I suggest looking elsewhere for the seals. __________________ 1990 Red on Red vin #2433

06-12-2007	#13
swaindm Join Date: Jun 2007 Location: 7559 McClellan Rd., Kaleva, MI 49645 Posts: 6	Re: fuel injectors 150821 is correct! I was confusing some non stock applications. Sorry!! DMS

07-14-2007	#16
george henry Join Date: Aug 2006 Location: San Diego, CA Posts: 24	Re: fuel injectors Hello. Just replaced all 16 injectors with Accel part number 150121 from Atlantic Speed for about $500. This took care of my high idle problem as well as a bad lack of power (bad stumble when the secondaries kick in), also replaced the PCV hose with the unit from White Racing and got new PCV valves. The old hose was a loose fit to the valves and this probably contributed to the high idle (1200 rpm), it now goes right to 750 rpm after start. The injectors were the originals and ethanol had taken its toll on them. I was a first timer on the plenum removal, it's not that big of a deal. 1990 #1507 __________________ 1990 #1507 Black/Grey/flowmaster-DRM chip

07-14-2007	#17
george henry Join Date: Aug 2006 Location: San Diego, CA Posts: 24	Re: fuel injectors Hello. Just replaced all 16 injectors with Accel part number 150121 from Atlantic Speed for about $500. This took care of my high idle problem as well as a bad lack of power (bad stumble when the secondaries kick in), also replaced the PCV hose with the unit from White Racing and got new PCV valves. The old hose was a loose fit to the valves and this probably contributed to the high idle (1200 rpm), it now goes right to 750 rpm after start. The injectors were the originals and ethanol had taken its toll on them. I was a first timer on the plenum removal, it's not that big of a deal. 1990 #1507 __________________ 1990 #1507 Black/Grey/flowmaster-DRM chip

06-16-2007	#15
ffvetteman Join Date: Jan 2005 Location: New Berlin WI Posts: 247	Re: fuel injectors Whew you guys got me nervous for a minute there!!! I got 16 150121's sitting on the table in front of me ready to go in. This week I hope Just need to get a hold of a set of spark plug wires now.

07-15-2007	#19
george henry Join Date: Aug 2006 Location: San Diego, CA Posts: 24	Re: fuel injectors Just read Roger E's post about using the outer slot on the injector for the clip to the fuel rail (the slot next to the o-ring?) I just pushed them into the rail and used the slots that look like they were made for the clip. There were no leaks and it runs fine. Does anybody know how much difference this makes? Should I worry? __________________ 1990 #1507 Black/Grey/flowmaster-DRM chip

07-15-2007	#20
Jagdpanzer Join Date: Apr 2007 Location: Northern VA Posts: 2,661	Re: fuel injectors So do the Accel 150121 injectors work in both the 375 and 405 hp LT5 engines?