Camber Brace Help - ZR-1 Net Registry Forums

CJ_ZR1 · 06-01-2013

Pickup up this R-D Camber Brace a few months ago. Finally completed coilover and sway bars installs and now ready to install camber brace before getting an alignment, but having a little trouble figuring out how this brace is installed. Do I have all the parts needed for install? Anyone have good pics of brace to help? Thanks in advance for any info

Funracer · 06-02-2013

I have one installed. Stand bye while I get a pic.

Funracer · 06-02-2013

Left Side (drivers side):

Right side (Pax side) looking down at it:

Crossbar running underneath front of the air horn. Tight fight:

Mine is an early one I think 10+ yrs old. Yours may not be exactly
the same. As I remember the DS crossbar-to-short-cornerpiece bolt
was a bi-atch to tighten due to limited access with the tools I had then.

On the plus side, it works great once you get it installed!

Good luck

CJ_ZR1 · 06-02-2013

Quote:

Originally Posted by Funracer

I have one installed. Stand bye while I get a pic.

Thanks for the quick reply and pics. Best pics I have seen of one installed, there are tons of pics for L98 and LT1 cars but not so much for the Z. I will hopefully have time tonight to take a look and try to install. Thanks again

Tony Davila · 06-02-2013

JimZRyd · 06-02-2013

What coil overs and sways did you go with? Have heard people talk about c/o's on their Z's but haven't heard much about sways. On my old C5 I went with a c/o system from Pfadt racing and put larger sways from the C6Z51 system. Might be something I do on my 94 down the road. Thanks!

CJ_ZR1 · 06-02-2013

Quote:

Originally Posted by JimZRyd

What coil overs and sways did you go with? Have heard people talk about c/o's on their Z's but haven't heard much about sways. On my old C5 I went with a c/o system from Pfadt racing and put larger sways from the C6Z51 system. Might be something I do on my 94 down the road. Thanks!

I went with DRM coilovers (dougrippie.com) and VBP sway bars (vbandp.com). Went with 32mm front and 26mm rear solid bars. Will post pics soon.

-CJ

JimZRyd · 06-02-2013

Quote:

Originally Posted by CJ_ZR1

I went with DRM coilovers (dougrippie.com) and VBP sway bars (vbandp.com). Went with 32mm front and 26mm rear solid bars. Will post pics soon.

-CJ

How was your ride after the install? Do you track your car? I'm not a track junky but do like to do some " spirited " driving. When I took my old C5 from stock and added c/ o's, sways, non run flats, and a thicker tunnel brace, and then sat her down in the weeds she was a totally different car. Rode smooth as anything but would stay totally flat through any twisty. Looking forward to your pics! Be sure to show off your stance

Coupe89 · 06-04-2013

Cool pics. I need to install mine... one day

06-01-2013	#1
CJ_ZR1 Join Date: Apr 2012 Location: Pineville, Louisiana Posts: 57	Camber Brace Help Pickup up this R-D Camber Brace a few months ago. Finally completed coilover and sway bars installs and now ready to install camber brace before getting an alignment, but having a little trouble figuring out how this brace is installed. Do I have all the parts needed for install? Anyone have good pics of brace to help? Thanks in advance for any info __________________ CJ Daniel [B]1991[/B] ZR-1 #834 [COLOR=royalblue][B]Steel Blue Metallic/Steel Blue[/B][/COLOR] [COLOR=red]Frank Approved ZR-1[/COLOR] [SIZE=1]- Ported air horn, throttle body, plenum and injector housings (Tommy Morrison)[/SIZE] [SIZE=1]- FIC SS Injectors / Nology hot wires / Screemin Deamin coils[/SIZE] [SIZE=1]- Fluidyne aluminum radiator and 9 row aluminum oil cooler[/SIZE] [SIZE=1]- 4.10 gears / Fidanza light weight flywheel / Hurst short throw shifter[/SIZE] [SIZE=1]- Stainless Works long tube headers / Borla exhaust with x-pipe[/SIZE] [SIZE=1]- DRM Coilovers / 32mm front 26mm rear sway bars[/SIZE] [SIZE=1]- ASM bolt in 4 point roll bar[/SIZE] [SIZE=1]- 93 ZR-1 Sawblades[/SIZE]

06-02-2013	#2
Funracer Join Date: Oct 2011 Location: Shalimar, FL Posts: 192	Re: Camber Brace Help I have one installed. Stand bye while I get a pic.

06-02-2013	#3
Funracer Join Date: Oct 2011 Location: Shalimar, FL Posts: 192	Re: Camber Brace Help Left Side (drivers side): Right side (Pax side) looking down at it: Crossbar running underneath front of the air horn. Tight fight: Mine is an early one I think 10+ yrs old. Yours may not be exactly the same. As I remember the DS crossbar-to-short-cornerpiece bolt was a bi-atch to tighten due to limited access with the tools I had then. On the plus side, it works great once you get it installed! Good luck

06-02-2013	#5
Tony Davila Join Date: Jan 2004 Location: Enterprise, Alabama Posts: 352	Re: Camber Brace Help __________________ Tony Davila (Projects) Water Meth: http://www.zr1.net/forum/showthread.php?t=19422 Exhaust cut outs: http://www.zr1.net/forum/showthread.php?t=22689 Auxiliary 12V install: http://www.zr1.net/forum/showthread.php?t=22878 Auxiliary pusher fan install: http://www.zr1.net/forum/showthread.php?t=22859 Oil Catch can Project: http://www.zr1.net/forum/showthread.php?t=20320

06-02-2013	#6
JimZRyd Join Date: Jan 2012 Location: Florence, SC Posts: 1,345	Re: Camber Brace Help What coil overs and sways did you go with? Have heard people talk about c/o's on their Z's but haven't heard much about sways. On my old C5 I went with a c/o system from Pfadt racing and put larger sways from the C6Z51 system. Might be something I do on my 94 down the road. Thanks! __________________ Jim Zorgias 1994 ZR-1 Admiral Blue/Black #245 1996 Callaway Supernatural 450 1990 Callaway Supernatural 490 / CR-1 #7

06-04-2013	#9
Coupe89 Join Date: Aug 2009 Location: Livermore, Ca Posts: 204	Re: Camber Brace Help Cool pics. I need to install mine... one day __________________ 1990 ZR-1 #642