|
04-05-2008
|
#1 |
 
Join Date: Nov 2007
Location: Sykesville, MD
Posts: 377
|
What is this?
So, after some encouragement from Uly (thanks!!
 I needed that), I decided to dive into a plenum pull/injector replacement myself tonight - instead of paying a few guys to help out.The plenum is off, new wires are on, new injectors are in the rail and I'm ready to start buttoning it back up... then I see this horrendous-looking thing runing from one bank to the other under where the rear of the plenum should go: http://i256.photobucket.com/albums/h...1/IMG_1705.jpg. I have no idea how I didn't notice the condition of the hose during the removal - it's nearly cracked in half at three places! I an 98% sure that this is the PCV hose and valves, but before I go off and order a new ones, I thought I'd make sure that I am asking for the right parts and see if anyone knows of a more economical solution than ordering from Kurt White? I'll call the local Autozone, Checkers, NAPA, etc. tomorrow, but I'm not optimistic that I'll find what I need local. Thanks!!
__________________
WAZOO Member '95 Callaway SNAT 450 Aerobody Coupe - Black/Black '92 Callaway SNAT 400 Convertible - Polo Green/Beige '91 ZR-1 #1231 - Arctic White/Saddle (SOLD) '90 ZR-1 #2547 - Turquoise Metallic/Black '89 Callaway Twin Turbo Aerobody Coupe #027 - Black/Black '85 Corvette 454 Coupe - White/Red |
|
|
|
04-05-2008
|
#2 |
|
Guest
Posts: n/a
|
Re: What is this?
LOL, damn somebody really did a shade tree fix on that.
it's the PCV hose. You can only get it from Kurt. http://www.whiteracingproducts.com/i...oducts_id=1012 |
|
|
|
04-05-2008
|
#3 | |
Join Date: Aug 2006
Location: Edmonton, Alberta or Phoenix, Arizona
Posts: 2,741
|
Re: What is this?
Quote:
 LOL. will be that much better when you get it together
__________________
There are no limit's mans ingenuity, just as mans ingenuity will never conquer the forces & behavior of this planet...Smokey Y. |
|
|
|
|
|
04-05-2008
|
#4 |
|
Join Date: Nov 2007
Location: Sykesville, MD
Posts: 377
|
Re: What is this?
Jeff,
That "somebody" would be Corvette Connection here in the Denver area... obviously not a "preferred" LT5 service location.Thanks for verifying the sole source for the part. Damn expensive hose... and it was all going so smoothly until I saw that!! Scott
__________________
WAZOO Member '95 Callaway SNAT 450 Aerobody Coupe - Black/Black '92 Callaway SNAT 400 Convertible - Polo Green/Beige '91 ZR-1 #1231 - Arctic White/Saddle (SOLD) '90 ZR-1 #2547 - Turquoise Metallic/Black '89 Callaway Twin Turbo Aerobody Coupe #027 - Black/Black '85 Corvette 454 Coupe - White/Red |
|
|
|
|
04-05-2008
|
#5 |
|
Guest
Posts: n/a
|
Re: What is this?
The zip tie wasn't really a problem. But the two large cracks in the hose are. Probably not helping your emissions.
|
|
|
|
04-05-2008
|
#6 |
|
Join Date: Nov 2007
Location: Sykesville, MD
Posts: 377
|
Re: What is this?
"didn't even use a black zip-tie to try & hide
" ... very funny. I agree that black would have been MUCH BETTER. I forgot to rant about the zip tie and how the whole monstrocity basically fell apart when I touched it! It not only looks terrible, it doesn't even hold it together good!!
__________________
WAZOO Member '95 Callaway SNAT 450 Aerobody Coupe - Black/Black '92 Callaway SNAT 400 Convertible - Polo Green/Beige '91 ZR-1 #1231 - Arctic White/Saddle (SOLD) '90 ZR-1 #2547 - Turquoise Metallic/Black '89 Callaway Twin Turbo Aerobody Coupe #027 - Black/Black '85 Corvette 454 Coupe - White/Red |
|
|
|
|
04-05-2008
|
#7 |
 
Join Date: Dec 2004
Location: Jacksonville, FL USA
Posts: 4,645
|
Re: What is this?
Man, that's just plain ole ugly! It hurts just to look at it.
That piece of hose has to be in the top 3 most expensive rubber parts on a Z! 
__________________
1990 ZR-1, Black/grey, #2233, stock. ZR-1 Net Reg Founding Member #316 & NCM member |
|
|
|
|
04-05-2008
|
#8 | |
 
Join Date: Jul 2007
Location: Bartlett, IL
Posts: 7,169
|
Re: What is this?
Quote:
__________________
1990 Corvette ZR-1 #1051 Watson Headers (2" Primary) - Flowmaster Cats - Borla Catback Late Model IH - Plenum Coilovers - 4.10s Custom Interior NCM Lifetime Member #978 |
|
|
|
|
|
04-05-2008
|
#9 |
|
Join Date: Jul 2007
Location: Bartlett, IL
Posts: 7,169
|
Re: What is this?
Actually the aftermarket part is better thent he OEM at $250
PCV valves are not too bad at $14 but are those LT5 specific or will others form the local parts place work?
__________________
1990 Corvette ZR-1 #1051 Watson Headers (2" Primary) - Flowmaster Cats - Borla Catback Late Model IH - Plenum Coilovers - 4.10s Custom Interior NCM Lifetime Member #978 |
|
|
|
|
04-05-2008
|
#10 |
Join Date: Nov 2007
Location: Sunshine State
Posts: 1,071
|
Re: What is this?
Hey when I did my plenum pull, I noticed the inj housing bolts were all pretty loose. Check them & the breather box bolts. My breather box bolts were finger tight!!
__________________
[B]1990 #2815[/B] [COLOR="Red"][B]Red/Red[/B][/COLOR] Ported Plenum & IH (by Pete) Haibeck Chip Rebuilt FPR (by Phil) FIC Injectors Watson LT Headers 3" Stainless Works exhaust Lingenfelter Open Air Lid Bill B Built Transmission Shifter & C Beam Plates [FONT=Impact][COLOR=red]1992 [COLOR=black]#[/COLOR] 091[/COLOR][/FONT] [FONT=Impact][COLOR=#ff0000]Red/[COLOR=silver]Gray[/COLOR][/COLOR][/FONT] [B]SOLD[/B] |
|
|
|
 |
| Thread Tools | |
| Display Modes | |
|
|
Linear Mode
