|
03-20-2022
|
#1 |
 Join Date: Oct 2019
Location: Mansfield, TX
Posts: 148
|
1992 How to Remove Dash Defroster Vent
1992 - how to remove dash defroster vent?
Appears to clip in. Don't want to break the brittle plastic. Removing defroster vent to fish a Sirius satellite radio antenna lead. Thanks, Gary .... 
|
|
|
|
03-20-2022
|
#2 |
 Join Date: Aug 2006
Location: McLean, VA
Posts: 3,723
|
Re: 1992 How to Remove Dash Defroster Vent
if I remember correct, push the rear lightly forward as you lift up the rear of the trim.
Attached link to trim pics should help. https://www.ebay.com/itm/13397173120...36ee070ffedec7 |
|
|
|
03-21-2022
|
#3 |
|
Join Date: Oct 2019
Location: Mansfield, TX
Posts: 148
|
Re: 1992 How to Remove Dash Defroster Vent
2nd Chance,
Awesome info on the dash defroster removal. Appreciate the e-bay link. Thanks, Gary .... |
|
|
|
|
03-21-2022
|
#4 |
 
Join Date: Apr 2007
Location: Lake Bluff, IL
Posts: 2,095
|
Re: 1992 How to Remove Dash Defroster Vent
I had Marc H. install my V1 radar detector cord (wired into the fuse panel on right of passenger side dash). FYI, when the grille was out, he cut a small notch in the driver's side edge for the V1 power cord so it fit back together flush and stock looking. The V1 fit perfectly in the windshield cutout, right above (and holding down) my I-Pass toll transponder. --Bob
__________________
2016 Long Beach Red Z06 #10281 "POPS Z" 1995 Polo Green #409 "WARP TEN"--Haibeck 350/510 package, 4.10s, Hurst, Stock Exhaust with QTP Cutouts --Sold but still running strong 1993 Quasar Blue #161 "HIL KING" --Sold but still running strong, now with more than 120,000 miles 1967 Marlboro Maroon/Saddle Corvette Coupe 300 hp/4-spd --Sold a long time ago ZR-1 Net Registry Founding Member #95 NCM Lifetime Member Favorite Quote--Attributed to Mickey Thompson: "Too Much Horsepower is Almost Enough" |
|
|
|
|
03-21-2022
|
#5 |
Join Date: Jul 2007
Location: Bartlett, IL
Posts: 7,169
|
Re: 1992 How to Remove Dash Defroster Vent
Where are you putting the XM antenna? I had mine on top of that vent and it was ok. I relocated it to the hatch mounted to the glass as I felt the Windshield was causing a bit of attenuation and caused some drop outs
__________________
1990 Corvette ZR-1 #1051 Watson Headers (2" Primary) - Flowmaster Cats - Borla Catback Late Model IH - Plenum Coilovers - 4.10s Custom Interior NCM Lifetime Member #978 |
|
|
|
|
03-21-2022
|
#6 |
|
Join Date: Aug 2006
Location: McLean, VA
Posts: 3,723
|
Re: 1992 How to Remove Dash Defroster Vent
Sorry. I didn't read the entire post. I agree with Jeff. I would try mounting the sat radio antenna under the plastic trim under rear hatch trim. Nav antenna works fine under the plastic trim without cutting and fitting.
If OEM windshield with reflector film could cause signal drop out. |
|
|
|
|
03-22-2022
|
#7 |
|
Join Date: Oct 2019
Location: Mansfield, TX
Posts: 148
|
Re: 1992 How to Remove Dash Defroster Vent
2nd Chance, Jeff and Bob,
Got the defroster bezel out in one piece, thanks to y'all sage guidance. The satellite antenna will be in the driver's side windshield "safe" spot area. When I tested my Garmin GPS it didn't have any problem locating the GPS satellites and works ok. Plan to add a notch the on the driver's side of the defroster bezel to feed the antenna coax through and same on the glove box side. Thanks again, Gary .... Last edited by chesnut; 03-22-2022 at 03:55 PM. |
|
|
|
|
03-22-2022
|
#8 |
|
Join Date: Oct 2019
Location: Mansfield, TX
Posts: 148
|
Re: 1992 How to Remove Dash Defroster Vent
Guys,
In case a backup plan is needed - would appreciate how y'all routed the satellite antenna coax to and under the rear hatch plastic trim. Did you notch a slot for the antenna coax in the rear of the console or ? Many thanks, Gary .... |
|
|
|
 |
| Thread Tools | |
| Display Modes | |
|
|
Linear Mode
