Pulled plenum...lots a ??'s - Page 4 - ZR-1 Net Registry Forums

tf95ZR1 · 01-19-2008

Hey 32 V
You might want to cover over the IH holes while you wait
or are working. Sure wouldn't want to drop something down
the endless hole...... or spill.... or

PS Damn, you sure cleaned up that valley purdy.

32valvZ · 01-19-2008

Got it done...duck tape over the holes..

Nick · 01-19-2008

Quote:

Originally Posted by 32valvZ

I would like the Accel coils...are the Accel injectors ok?

I had an Accel coil failure after two years and about 6,000 miles of driving. Replaced with the MSD's for approximately the same $$. All is well now. I've heard of at least one other Accel coil failure in the last few years. The stock coils are also an excellent choice. FWIW.
I'm heading to the Accel injectors as well. Hope it turns out well for both of us!

32valvZ · 01-19-2008

...I already ordered the Accels coils & injectors....I'll have to hope for the best!

bradslt5 · 01-19-2008

when buying the accels do you need special o rings for them? if so where so you get them?

Zr1 Destroyer · 01-19-2008

John, your an animal buddy.........how did it look under there!?

Ry

Zr1 Destroyer · 01-19-2008

Also........yank the coil packs and starter(if you already havn't) and pressure wash the hell out of it!!! How did your secodaries look and feel?

32valvZ · 01-20-2008

Quote:

Originally Posted by Zr1 Destroyer

Also........yank the coil packs and starter(if you already havn't) and pressure wash the hell out of it!!! How did your secodaries look and feel?

Hey Ry.....I removed pretty much everything in the valley....breather box included. It was pretty grimey....like you said, thats probably where the burnt oil smell was coming from (brthr box gasket). The breather box bolts were loose as heck!! I am replacing coils, injectors and all needed gaskets. I'm getting a vacuum pump today to check the secondary actuators. (old one broke)....anyway, Jeffvette was saying how 1/2 the new ones available were bad.....I would like to buy a couple for insurance & just install them. I guess I need to buy 12 at a time!!! Looking to get the dealer to test them for me before I buy.....

Paul Workman · 01-21-2008

Quote:

Originally Posted by DMark

WOW, this thread is great! I'm about to do a plenum pull and this is a great refresher!

I'm also a noobee to the Z, and also poised over the plenum. I was going to wait till I could afford to do the whole nine yards, but from hearing 'bout the loose IH bolts, that alone would warrant investigation. Injectors might have to wait, but I think it's time to dive in and have a look-around!

Like you said, GREAT THREAD!

P.

Paul Workman · 01-21-2008

Quote:

Originally Posted by 32valvZ

I am replacing coils, injectors and all needed gaskets. I'm getting a vacuum pump today to check the secondary actuators. (old one broke)....anyway, Jeffvette was saying how 1/2 the new ones available were bad.....I would like to buy a couple for insurance & just install them. I guess I need to buy 12 at a time!!! Looking to get the dealer to test them for me before I buy.....

Sorry to be so obtuse, but 1/2 of what are bad?

TIA

,

P.

01-19-2008	#31
tf95ZR1 Join Date: Aug 2005 Location: Northridge, CA Posts: 1,461	Re: Pulled plenum...lots a ??'s Hey 32 V You might want to cover over the IH holes while you wait or are working. Sure wouldn't want to drop something down the endless hole...... or spill.... or PS Damn, you sure cleaned up that valley purdy. Last edited by tf95ZR1; 01-19-2008 at 01:25 AM.

01-19-2008	#32
32valvZ Join Date: Nov 2007 Location: Sunshine State Posts: 1,071	Re: Pulled plenum...lots a ??'s Got it done...duck tape over the holes.. __________________ [B]1990 #2815[/B] [COLOR="Red"][B]Red/Red[/B][/COLOR] Ported Plenum & IH (by Pete) Haibeck Chip Rebuilt FPR (by Phil) FIC Injectors Watson LT Headers 3" Stainless Works exhaust Lingenfelter Open Air Lid Bill B Built Transmission Shifter & C Beam Plates [FONT=Impact][COLOR=red]1992 [COLOR=black]#[/COLOR] 091[/COLOR][/FONT] [FONT=Impact][COLOR=#ff0000]Red/[COLOR=silver]Gray[/COLOR][/COLOR][/FONT] [B]SOLD[/B]

01-19-2008	#34
32valvZ Join Date: Nov 2007 Location: Sunshine State Posts: 1,071	Re: Pulled plenum...lots a ??'s ...I already ordered the Accels coils & injectors....I'll have to hope for the best! __________________ [B]1990 #2815[/B] [COLOR="Red"][B]Red/Red[/B][/COLOR] Ported Plenum & IH (by Pete) Haibeck Chip Rebuilt FPR (by Phil) FIC Injectors Watson LT Headers 3" Stainless Works exhaust Lingenfelter Open Air Lid Bill B Built Transmission Shifter & C Beam Plates [FONT=Impact][COLOR=red]1992 [COLOR=black]#[/COLOR] 091[/COLOR][/FONT] [FONT=Impact][COLOR=#ff0000]Red/[COLOR=silver]Gray[/COLOR][/COLOR][/FONT] [B]SOLD[/B]

01-19-2008	#35
bradslt5 Join Date: Oct 2007 Location: lone pine and mammoth lakes ca. Posts: 544	Re: Pulled plenum...lots a ??'s when buying the accels do you need special o rings for them? if so where so you get them?

01-19-2008	#36
Zr1 Destroyer Join Date: Oct 2005 Location: Candy Apple...yUmMy Posts: 1,137	Re: Pulled plenum...lots a ??'s John, your an animal buddy.........how did it look under there!? Ry

01-19-2008	#37
Zr1 Destroyer Join Date: Oct 2005 Location: Candy Apple...yUmMy Posts: 1,137	Re: Pulled plenum...lots a ??'s Also........yank the coil packs and starter(if you already havn't) and pressure wash the hell out of it!!! How did your secodaries look and feel?

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode