|
05-17-2013
|
#1 |
 
Join Date: Jul 2007
Location: Bartlett, IL
Posts: 7,156
|
Dash Pad swap..
now I know why it was not fitting right around the Defrost vent..
The squares in the circled area are suppose to be a small screw hole only.. LOL   Bad Carpet Dye job done before I got the car..  Couple pieces getting prepared to be installed  
__________________
1990 Corvette ZR-1 #1051 Watson Headers (2" Primary) - Flowmaster Cats - Borla Catback Late Model IH - Plenum Coilovers - 4.10s Shelby Series 1 - Wilwood Brakes Custom Interior NCM Lifetime Member #978 |
|
|
|
05-18-2013
|
#2 |
|
Join Date: Jul 2007
Location: Bartlett, IL
Posts: 7,156
|
Re: Dash Pad swap..
Old dash did not fit right around the defrost vent..
 Better fit and a hidden GPS antenna now:  New Hush panel on Driver side.  New pass side carpet on Dash: 
__________________
1990 Corvette ZR-1 #1051 Watson Headers (2" Primary) - Flowmaster Cats - Borla Catback Late Model IH - Plenum Coilovers - 4.10s Shelby Series 1 - Wilwood Brakes Custom Interior NCM Lifetime Member #978 |
|
|
|
|
05-19-2013
|
#3 |
|
Join Date: Jul 2007
Location: Bartlett, IL
Posts: 7,156
|
Re: Dash Pad swap..
Done.. it is a bit better but unfortunately not perfect
__________________
1990 Corvette ZR-1 #1051 Watson Headers (2" Primary) - Flowmaster Cats - Borla Catback Late Model IH - Plenum Coilovers - 4.10s Shelby Series 1 - Wilwood Brakes Custom Interior NCM Lifetime Member #978 |
|
|
|
|
06-16-2013
|
#4 |
 
Join Date: Sep 2012
Location: Westminster, Md.
Posts: 434
|
Re: Dash Pad swap..
Hello Jeff,
Did you have to remove your dashpad? If so can you tell me how to remove it. I have to remove mine and having problem finding all the fasteners holding it to the frame. Thanks, Nelson 007 |
|
|
|
|
06-16-2013
|
#5 |
|
Join Date: Jul 2007
Location: Bartlett, IL
Posts: 7,156
|
Re: Dash Pad swap..
to remove.. need to remove:
Pass side trim around Fuse panel Lower hush panels Driver side panel against door Headlight switch Cluster bezel all 3 vents Console and radio bezel Defrost vent Glovebox and lid Dash pad has screws by the center vent, 2 at the defrost vent, 2 above the Cluster With the vents removed the dash should pull out, it is a bit tight as there are 4 clips along the windshield edge holding it in to the car
__________________
1990 Corvette ZR-1 #1051 Watson Headers (2" Primary) - Flowmaster Cats - Borla Catback Late Model IH - Plenum Coilovers - 4.10s Shelby Series 1 - Wilwood Brakes Custom Interior NCM Lifetime Member #978 |
|
|
|
|
06-16-2013
|
#6 |
|
Join Date: Sep 2012
Location: Westminster, Md.
Posts: 434
|
Re: Dash Pad swap..
Jeff thanks a million,
I will give it a try tomorrow,and let you know how it turns out. Have a good evening, Nelson |
|
|
|
 |
| Thread Tools | |
| Display Modes | |
|
|
Linear Mode
