ZR-1 Net Registry Forums  

Go Back   ZR-1 Net Registry Forums > C4 ZR-1 > C4 ZR-1 Technical Postings

Reply
 
Thread Tools Display Modes
Old 04-10-2011   #1
| 1990 ZR-1 |
 
Join Date: Feb 2011
Location: Medford, NJ
Posts: 77
Default New Brakes....No Stopping Power....help please

I just finished a full brake overhaul with new rotors, new Hawk HPS Pads, braided stainless steel brake lines, and flushed the fluid with Synthetic fluid. Dark brown gunk came out with little rust pieces especailly out of the front calipers. I did go through two botlles of fluid just to make sure all the crap was out. I managed to get air into the master cylinder, which I bench bled the get the air out of it nad properly bled all four corners again (RR, RL, FR, FL). I also went through the proper procedure of bedding the pads, but after all this, I still have a somewhat soft pedal feel with long travel. I'm not really sure if this how the brakes on the ZR-1 suppose to perform since it's my first corvette, but they feel unsafe. The car brakes and stops, but does so with a huge effort, and the ABS does not kick in. It feels like the brakes do not match the power of the car. I' afraid to accelarate too fast in trafic in case I have to stop suddenly. I try to keep a safer distnace than normal so I don't rear end any one. It just doesn't seem normal. My only conclussion is there's either something wrong with the master cylinder or the brake booster, or both. How would I check if either one or both are bad?? They seem to be verry expensive to replace. There's no air hissing sound coming out of the brake booster.Does that mean it's okay? is there anything else I need to check?

Thanks in advance guys!

On a side note, I also finished installing the FX3 suspenssion and it works flawlessly!!
| 1990 ZR-1 | is offline   Reply With Quote
Old 04-10-2011   #2
mike100
 
Join Date: Feb 2011
Location: San Marcos CA
Posts: 1,802
Default Re: New Brakes....No Stopping Power....help please

You probably still have air in the system, but even if you do get a hard pedal when you pump the brakes a couple of times, I'd say maybe you just need to put 30 or 40 miles on those pads because they will be terrible until they really bed in (depending on compound).

Not sure how to diagnose your vacuum booster. My non-ZR-1 95 coupe had terrible power boost, but my 91 ZR-1 with the double diaphragm brake booster is twice as good.

try to bleed the rears again...that firmed up my pedal (which was crap when I acquired the car).

ON EDIT: I now have brand new C5 calipers on my fronts with a lot more pad area, but even my stock J55 calipers were good enough to lock up the brakes a couple of times once fully bled.

Last edited by mike100; 04-10-2011 at 02:26 PM.
mike100 is offline   Reply With Quote
Old 04-10-2011   #3
Aurora40
 
Aurora40's Avatar
 
Join Date: May 2005
Location: Leesburg, VA
Posts: 2,713
Default Re: New Brakes....No Stopping Power....help please

You can lock the tires and no ABS? Or you can't lock the tires?
__________________
Bob Saveland
Former owner of #2517

[IMG]http://a.random-image.net/aurora40/vette.jpg[/img]
Aurora40 is offline   Reply With Quote
Old 04-10-2011   #4
| 1990 ZR-1 |
 
Join Date: Feb 2011
Location: Medford, NJ
Posts: 77
Default Re: New Brakes....No Stopping Power....help please

Quote:
Originally Posted by Aurora40 View Post
You can lock the tires and no ABS? Or you can't lock the tires?
Hey Bob,

The pedal is pressed all the way down, but there's not enough braking power to lock the tires for the ABS to kick in.
| 1990 ZR-1 | is offline   Reply With Quote
Old 04-10-2011   #5
| 1990 ZR-1 |
 
Join Date: Feb 2011
Location: Medford, NJ
Posts: 77
Default Re: New Brakes....No Stopping Power....help please

Quote:
Originally Posted by Aurora40 View Post
You can lock the tires and no ABS? Or you can't lock the tires?

Bob, I found a similar post by you in 2009, but you never posted your resolution. How did you end up fixing your issue if you still remember?
| 1990 ZR-1 | is offline   Reply With Quote
Old 04-10-2011   #6
gbrtng
 
gbrtng's Avatar
 
Join Date: Feb 2006
Location: San Antonio area
Posts: 1,179
Default Re: New Brakes....No Stopping Power....help please

You still have an air bubble in the system somewhere if the pedal is not rock hard with
the booster depleted of vacuum. My preferred bleed sequence is RR. LR, RF, LF, and
I use the 2-man procedure.

What bleeding procedure and equipment did you use?
__________________
“Buy the best example of what you want, and pay whatever it takes. That way, you cry only once.” ~ Bruce Meyer
gbrtng is offline   Reply With Quote
Old 04-10-2011   #7
| 1990 ZR-1 |
 
Join Date: Feb 2011
Location: Medford, NJ
Posts: 77
Default Re: New Brakes....No Stopping Power....help please

Quote:
Originally Posted by gbrtng View Post
You still have an air bubble in the system somewhere if the pedal is not rock hard with
the booster depleted of vacuum. My preferred bleed sequence is RR. LR, RF, LF, and
I use the 2-man procedure.

What bleeding procedure and equipment did you use?
I'm really hoping that's the case. I bled the right rear then left rear, then right front and left front. I had my wife pump the brake pedal twice and hold it while I opened and closed the bleeders all while topping off the reservoir with new fluid.
| 1990 ZR-1 | is offline   Reply With Quote
Old 04-10-2011   #8
mike100
 
Join Date: Feb 2011
Location: San Marcos CA
Posts: 1,802
Default Re: New Brakes....No Stopping Power....help please

I had a little trouble with my rears not having much volume or squirt, but I think I just went over it about 3 times until they all had a strong flow of clean fluid. I think there was a little goo in the bleeder end.
mike100 is offline   Reply With Quote
Old 04-10-2011   #9
Aurora40
 
Aurora40's Avatar
 
Join Date: May 2005
Location: Leesburg, VA
Posts: 2,713
Default Re: New Brakes....No Stopping Power....help please

Quote:
Originally Posted by | 1990 ZR-1 | View Post
Bob, I found a similar post by you in 2009, but you never posted your resolution. How did you end up fixing your issue if you still remember?
Can you post a link? I don't recall having that problem. The biggie I had was installing Baer 6-pot calipers, the OEM banjo bolt was too long and was pressing the piston out. I couldn't get the car to *not* brake, they dragged really badly. Baer sent me a shorter bolt.

I did have a longer pedal after that. The DRM brake spring helped, but there's no getting around the larger piston displacement. They weren't scary, though.

Hmm, well one time they were scary at the dragstrip (braking from 115, they'd give out by around 80), but that was due to the sissy ceramic pads Baer included. A swap to Hawk's cured that.

It does sound like you have air in your lines, though. Also, supposedly it's not a good idea to press the pedal to bleed, as you can move the pedal through longer travel than it experiences normally, and can jack up seals. I dunno how true that is. I use a Mityvac to bleed brakes, and then gravity bleed to get any air that was sucked in around the bleed screw.
__________________
Bob Saveland
Former owner of #2517

[IMG]http://a.random-image.net/aurora40/vette.jpg[/img]

Last edited by Aurora40; 04-10-2011 at 07:31 PM.
Aurora40 is offline   Reply With Quote
Old 04-10-2011   #10
BlackWidow#2
 
BlackWidow#2's Avatar
 
Join Date: Feb 2004
Location: Pittsburgh, PA
Posts: 149
Default Re: New Brakes....No Stopping Power....help please

Did you bleed the ABS unit? You have air somewhere in the system I would bet.
__________________
[SIGPIC][/SIGPIC]George C

91 Black/Black ZR1, #2 of 8 black widow cars

15 black/red Z06

:hello:
BlackWidow#2 is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 11:23 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright ZR-1 Net Registry 2020