|
|
|
02-21-2009
|
#1 |
 
Join Date: Jul 2007
Location: Bartlett, IL
Posts: 7,180
|
Leaky Cam Covers?
anyone have this problem?
I was under the car looking for soemhting and noticed the cam covers are damp/ wet along the seam surface to the heads.. Reading Jeffvette's R&R procedrures on PNWZR1 makes it look easy.. but any specific Assembly lube? Also where can the the A136 sealant be gotten? Looks Like I will be able to refinish the cam covers this year after all
__________________
1990 Corvette ZR-1 #1051 Watson Headers (2" Primary) - Flowmaster Cats - Borla Catback Late Model IH - Plenum Coilovers - 4.10s Shelby Series 1 - Wilwood Brakes Custom Interior NCM Lifetime Member #978 |
|
|
|
02-21-2009
|
#2 |
 
Join Date: Aug 2006
Location: Texas
Posts: 518
|
Re: Leaky Cam Covers?
It might be well to make sure it's not the center stud in the exhaust manifold leaking before you you tear into a tougher fix. Cam covers seldom leak but a bunch of exhaust studs do when the seal gives up.
__________________
1991 ZR-1, Black, Black, # 541 |
|
|
|
|
02-21-2009
|
#3 |
Join Date: Mar 2007
Location: Crystal Lake, IL
Posts: 7,188
|
Re: Leaky Cam Covers?
I'd just run some stopleak through the engine.
NOT!
__________________
LGAFF 90 #966-150K miles-sold 92 #234-sold 1987 Callaway TT #17 1991 ZR-1 #1359 |
|
|
|
|
02-21-2009
|
#4 | |
|
Join Date: Jul 2007
Location: Bartlett, IL
Posts: 7,180
|
Re: Leaky Cam Covers?
Quote:
I have almost everything out of the way except the brake booster.. then the cam cover should be not too bad to remove, assuming all the bolts move..
__________________
1990 Corvette ZR-1 #1051 Watson Headers (2" Primary) - Flowmaster Cats - Borla Catback Late Model IH - Plenum Coilovers - 4.10s Shelby Series 1 - Wilwood Brakes Custom Interior NCM Lifetime Member #978 |
|
|
|
|
|
02-21-2009
|
#5 |
|
Join Date: Jul 2007
Location: Bartlett, IL
Posts: 7,180
|
Re: Leaky Cam Covers?
I am also doing headers this spring and really need to repaint the cam covers so may as well do it now
__________________
1990 Corvette ZR-1 #1051 Watson Headers (2" Primary) - Flowmaster Cats - Borla Catback Late Model IH - Plenum Coilovers - 4.10s Shelby Series 1 - Wilwood Brakes Custom Interior NCM Lifetime Member #978 |
|
|
|
|
02-21-2009
|
#6 |
|
Join Date: Mar 2007
Location: Crystal Lake, IL
Posts: 7,188
|
Re: Leaky Cam Covers?
Its not the cam position sensor is it....or maybe exhaust bolts are loose?
__________________
LGAFF 90 #966-150K miles-sold 92 #234-sold 1987 Callaway TT #17 1991 ZR-1 #1359 |
|
|
|
|
02-21-2009
|
#7 | |
|
Join Date: Jul 2007
Location: Bartlett, IL
Posts: 7,180
|
Re: Leaky Cam Covers?
Quote:
Again, the exhaust bolts are LOWER then where I see the oil at.. and I still think oil Cannot defy gravity.. if it can please enlighten me
__________________
1990 Corvette ZR-1 #1051 Watson Headers (2" Primary) - Flowmaster Cats - Borla Catback Late Model IH - Plenum Coilovers - 4.10s Shelby Series 1 - Wilwood Brakes Custom Interior NCM Lifetime Member #978 |
|
|
|
|
|
09-23-2009
|
#8 |
|
Join Date: Jul 2007
Location: Bartlett, IL
Posts: 7,180
|
Re: Leaky Cam Covers?
dynomite this is good advice for the next guy.. I did this about 7 months ago
__________________
1990 Corvette ZR-1 #1051 Watson Headers (2" Primary) - Flowmaster Cats - Borla Catback Late Model IH - Plenum Coilovers - 4.10s Shelby Series 1 - Wilwood Brakes Custom Interior NCM Lifetime Member #978 |
|
|
|
|
09-23-2009
|
#9 |
|
Join Date: Jul 2007
Location: Bartlett, IL
Posts: 7,180
|
Re: Leaky Cam Covers?
I used Jerry's washers..
also the 2" headers were not bad, only way to get Watsons is used
__________________
1990 Corvette ZR-1 #1051 Watson Headers (2" Primary) - Flowmaster Cats - Borla Catback Late Model IH - Plenum Coilovers - 4.10s Shelby Series 1 - Wilwood Brakes Custom Interior NCM Lifetime Member #978 |
|
|
|
 |
|
|
Hybrid Mode
