|
|
|
03-25-2020
|
#1 |
 
Join Date: Nov 2016
Location: Southlake, TX
Posts: 592
|
Squeaky sway bar bushings?
I'm getting a front end squeak as I go over some rough road and drive through my neighborhood. If I "bounce the car" I can replicate it. The front suspension is quiet when cold and gets louder after the car has been driven and the temperature outside heats up -- today was 91 in DFW.
My guess is that my bushings need attention. I want to swap them out with new ones and lube up the end links. Hopefully that will do the trick. I'm double checking that our front sway bars require 30mm bushings? Any thing else I need to lube up or inspect as long as I'm crawling around under the car?
__________________
Bill Schroeder Texas Proud! 1991 Corvette ZR1 #1388 2015 Challenger Scat Pack Shaker 
|
|
|
|
03-25-2020
|
#2 |
Join Date: Nov 2007
Location: Sunshine State
Posts: 1,071
|
Re: Squeaky sway bar bushings?
I thought the front was 26mm and the rear was 24mm
__________________
[B]1990 #2815[/B] [COLOR="Red"][B]Red/Red[/B][/COLOR] Ported Plenum & IH (by Pete) Haibeck Chip Rebuilt FPR (by Phil) FIC Injectors Watson LT Headers 3" Stainless Works exhaust Lingenfelter Open Air Lid Bill B Built Transmission Shifter & C Beam Plates [FONT=Impact][COLOR=red]1992 [COLOR=black]#[/COLOR] 091[/COLOR][/FONT] [FONT=Impact][COLOR=#ff0000]Red/[COLOR=silver]Gray[/COLOR][/COLOR][/FONT] [B]SOLD[/B] |
|
|
|
|
03-25-2020
|
#3 | |
|
Join Date: Nov 2016
Location: Southlake, TX
Posts: 592
|
Re: Squeaky sway bar bushings?
Quote:
__________________
Bill Schroeder Texas Proud! 1991 Corvette ZR1 #1388 2015 Challenger Scat Pack Shaker
|
|
|
|
|
|
03-25-2020
|
#4 |
|
Join Date: Nov 2007
Location: Sunshine State
Posts: 1,071
|
Re: Squeaky sway bar bushings?
This has some info on it...... Looks like 26/26 for a 91... my 90 is 26/24
__________________
[B]1990 #2815[/B] [COLOR="Red"][B]Red/Red[/B][/COLOR] Ported Plenum & IH (by Pete) Haibeck Chip Rebuilt FPR (by Phil) FIC Injectors Watson LT Headers 3" Stainless Works exhaust Lingenfelter Open Air Lid Bill B Built Transmission Shifter & C Beam Plates [FONT=Impact][COLOR=red]1992 [COLOR=black]#[/COLOR] 091[/COLOR][/FONT] [FONT=Impact][COLOR=#ff0000]Red/[COLOR=silver]Gray[/COLOR][/COLOR][/FONT] [B]SOLD[/B] Last edited by 32valvZ; 03-25-2020 at 10:55 PM. |
|
|
|
|
03-26-2020
|
#5 |
 
Join Date: Nov 2007
Location: Squires (near Ava MO in the Mark Twain N'tl Forest) - Missouri
Posts: 6,493
|
Re: Squeaky sway bar bushings?
If they are rubber, believe it or not, plain ol WD-40 is what we used in the shop. It pennitrates (creeps) between steel and rubber. Simple, cheap, & works great!
__________________
Good carz, good food, good friendz = the best of timez! 90 #1202 "FBI" top end ported & relieved Cam timing by "Pete the Greek" Sans secondaries Chip & dyno tuning by Haibeck Automotive SW headers, X-pipe, MF muffs Former Secretary, ZR-1 Net Registry |
|
|
|
|
03-26-2020
|
#6 | |
|
Join Date: Nov 2016
Location: Southlake, TX
Posts: 592
|
Re: Squeaky sway bar bushings?
Quote:
__________________
Bill Schroeder Texas Proud! 1991 Corvette ZR1 #1388 2015 Challenger Scat Pack Shaker
|
|
|
|
|
 |
|
|
Hybrid Mode
