No power to fuel pump, wiring help needed. - ZR-1 Net Registry Forums

nherbst454 · 01-13-2018

I just bought a 1990 ZR1 and am looking forward to get it running again. I purchased it from my widowed neighbor and the car has been sitting in storage for many years. I took the dash apart and found a massive mouse nest in the passenger side behind the dash. Most of the wires look to be in decent shape (a few have the insulation nibbled but I can fix that.)

I checked voltage to the fuel pumps and am getting nothing. I removed the fuel pumps and tested them by connecting the connectors directly to a battery and they are both dead (no humming).

I've removed the dash panel so I can access the relay connectors and am trying to figure out which relay is for the fuel pump and if I can jumper it when I get the new pumps installed. I will also take the relay out and test it but I probed the dark green / white wire which I believe is the pump 1 control signal from the ECM and I'm getting no signal to turn on the relay.

Any help would be appreciated!

New ZR-1 owner, Nate

RussMcB · 01-13-2018

Welcome, Nate. Glad to hear you are bringing a '90 ZR-1 back to life.

I'm afraid it's been too long since I've worked on my fuel pump to remember the details about that system. I think the FSM has troubleshooting steps to help you identify the problem(s). Marc Haibeck might be a good person to hook up with. He may even have something on his web site regarding the fuel system. It's worth your time to look at all of the technical information he has provided: http://www.zr1specialist.com

Ccmano · 01-13-2018

Here you go... from the 90 FSM Electrical Diagnosis Manual

nherbst454 · 01-14-2018

Thanks for the diagram. I checked the relay and it seems to work when hooked to a battery. I also checked that the ground is functional which it is and I have continuity from the output pin on the relay all the way to the fuel pump connector so the wiring seems to be good. Even with the key on I believe that the control signal (verified continuity of the control wire from the wire to the ECM) is not being commanded on by the computer.

I tried to scan codes using the digital dash, all I'm getting right now is H41 when it first scans then nothing when it says 1.0 or 4.0 ( I just get dashes).

Any thoughts on what could be causing the computer to not turn on the fuel pump output?

I'm not sure if it's important but I've also noticed that the security light flashes when the door is open but goes away when I turn the key on. Not sure if this is normal or not.

Thanks for all your help, I'm looking forward to getting this beauty back on the road!

nherbst454 · 01-14-2018

Any thoughts about the VATS causing no power to the fuel pump?

nherbst454 · 01-14-2018

I've ordered a FSM and it should be here sometime next week, does anyone know if the logic diagram for the ECU is in this? I'm trying to determine if the ECU needs to see some other inputs before it will turn on the fuel pump output.

Ccmano · 01-15-2018

Quote:

Originally Posted by nherbst454

Any thoughts about the VATS causing no power to the fuel pump?

Highly likely. However I’m not versed troubleshooting that system. Do a search on the forum. I’m reasonably sure there are volumes written on the subject.

Did you buy new pumps yet?
H

S.hafsmo · 01-15-2018

User WVZR-1 has electronic versions of both the FSM and the 8A electrical supplement you'd be able to aquire for a few $. These are also possible to do searches within.

nherbst454 · 01-24-2018

Update: I found out my issue was that the fuel pump is only activated for ~2 seconds after key on and each time I checked it at the connector it took more that 2 seconds to get to the back of the car!

New fuel pumps installed and she fired up. It does seem to take a few more rotations to start than I’m used to with newer cars, any thoughts on that? I’m thinking a fuel filter (car only has 5000 miles on it) and possibly removing the injectors to clean them.

Demps · 01-24-2018

Cut to the chase and replace the injectors too when you change filter.

Ted

An option that's served me well: Accel 150821 x2
Go to Autozone.com, add two to cart & select ship to home, input current discount code (SEE20 on 24 Jan 18). Shipped to your house <$510.

Go to jerrysgaskets.com & get plenum gaskets.

In your case, I'd look in starter valley for another rodent brothel. Be prepared to check all things for rat-snacking. Also, check vacuum condition.

01-13-2018	#1
nherbst454 Join Date: Jan 2018 Location: Woodbury, MN Posts: 11	No power to fuel pump, wiring help needed. I just bought a 1990 ZR1 and am looking forward to get it running again. I purchased it from my widowed neighbor and the car has been sitting in storage for many years. I took the dash apart and found a massive mouse nest in the passenger side behind the dash. Most of the wires look to be in decent shape (a few have the insulation nibbled but I can fix that.) I checked voltage to the fuel pumps and am getting nothing. I removed the fuel pumps and tested them by connecting the connectors directly to a battery and they are both dead (no humming). I've removed the dash panel so I can access the relay connectors and am trying to figure out which relay is for the fuel pump and if I can jumper it when I get the new pumps installed. I will also take the relay out and test it but I probed the dark green / white wire which I believe is the pump 1 control signal from the ECM and I'm getting no signal to turn on the relay. Any help would be appreciated! New ZR-1 owner, Nate

01-13-2018	#2
RussMcB Join Date: Jan 2015 Location: Marietta, GA USA Posts: 1,160	Re: No power to fuel pump, wiring help needed. Welcome, Nate. Glad to hear you are bringing a '90 ZR-1 back to life. I'm afraid it's been too long since I've worked on my fuel pump to remember the details about that system. I think the FSM has troubleshooting steps to help you identify the problem(s). Marc Haibeck might be a good person to hook up with. He may even have something on his web site regarding the fuel system. It's worth your time to look at all of the technical information he has provided: http://www.zr1specialist.com

01-13-2018	#3
Ccmano Join Date: Jun 2006 Location: Sparks, NV Posts: 2,852	Re: No power to fuel pump, wiring help needed. Here you go... from the 90 FSM Electrical Diagnosis Manual __________________ 90'ZR-1 #1461 Red/Black Ported Intake, Degreed Cams, OBX Headers & Exhaust, Fidanza FW, Secondary Delete, Custom tune, C6 GS Wheels. Sold 08 C6 Z51 Crystal Red Metallic Sold Vararam Intake, Tune, Sold 05 C6 Z51 Red/Black Sold 90'ZR-1 #1723 Black/Gray Sold but not forgotten 91' Z51 L98 White Vert. My First, you always remember your first. Sold.

01-14-2018	#4
nherbst454 Join Date: Jan 2018 Location: Woodbury, MN Posts: 11	Re: No power to fuel pump, wiring help needed. Thanks for the diagram. I checked the relay and it seems to work when hooked to a battery. I also checked that the ground is functional which it is and I have continuity from the output pin on the relay all the way to the fuel pump connector so the wiring seems to be good. Even with the key on I believe that the control signal (verified continuity of the control wire from the wire to the ECM) is not being commanded on by the computer. I tried to scan codes using the digital dash, all I'm getting right now is H41 when it first scans then nothing when it says 1.0 or 4.0 ( I just get dashes). Any thoughts on what could be causing the computer to not turn on the fuel pump output? I'm not sure if it's important but I've also noticed that the security light flashes when the door is open but goes away when I turn the key on. Not sure if this is normal or not. Thanks for all your help, I'm looking forward to getting this beauty back on the road!

01-14-2018	#5
nherbst454 Join Date: Jan 2018 Location: Woodbury, MN Posts: 11	Re: No power to fuel pump, wiring help needed. Any thoughts about the VATS causing no power to the fuel pump?

01-15-2018	#8
S.hafsmo Join Date: Nov 2016 Location: Norway Posts: 397	Re: No power to fuel pump, wiring help needed. User WVZR-1 has electronic versions of both the FSM and the 8A electrical supplement you'd be able to aquire for a few $. These are also possible to do searches within. __________________ - '90 ZR-1

01-24-2018	#9
nherbst454 Join Date: Jan 2018 Location: Woodbury, MN Posts: 11	Re: No power to fuel pump, wiring help needed. Update: I found out my issue was that the fuel pump is only activated for ~2 seconds after key on and each time I checked it at the connector it took more that 2 seconds to get to the back of the car! New fuel pumps installed and she fired up. It does seem to take a few more rotations to start than I’m used to with newer cars, any thoughts on that? I’m thinking a fuel filter (car only has 5000 miles on it) and possibly removing the injectors to clean them.

01-24-2018	#10
Demps Join Date: Jan 2006 Location: Niceville Posts: 998	Re: No power to fuel pump, wiring help needed. Cut to the chase and replace the injectors too when you change filter. Ted An option that's served me well: Accel 150821 x2 Go to Autozone.com, add two to cart & select ship to home, input current discount code (SEE20 on 24 Jan 18). Shipped to your house <$510. Go to jerrysgaskets.com & get plenum gaskets. In your case, I'd look in starter valley for another rodent brothel. Be prepared to check all things for rat-snacking. Also, check vacuum condition. Last edited by Demps; 01-24-2018 at 10:17 AM.