A moron needs some help. - ZR-1 Net Registry Forums

Z51JEFF · 11-04-2017

I've got a spare alternator I tore apart to rebuild now can't remember what order the 3 collars or spacers go,there are 2 that go on each side of the bearing and one between the fan and pulley. Anybody got the info on this? I've searched the net for a diagram,schematic but can't find anything. Thanks.

A26B · 11-04-2017

Scroll down in this thread for a picture

http://www.zr1.net/forum/showthread.php?t=27876

Z51JEFF · 11-04-2017

Quote:

Originally Posted by A26B

Scroll down in this thread for a picture

http://www.zr1.net/forum/showthread.php?t=27876

Thanks Jerry,that's the one.

WVZR-1 · 11-05-2017

Quote:

Originally Posted by A26B

Scroll down in this thread for a picture

http://www.zr1.net/forum/showthread.php?t=27876

In that snapshot Jerry this would be GM SPO info for the spacers/collars

.396 is actually 10mm x 25.5 diameter GM# 1978064 (WAI 46-1601-1)

.232 is actually 5.8mm x 25.5 diameter GM# 1985999 (WAI 46-1617-1)

If a person were needing these the WAI information would likely be used by all after-market vendors.

A26B · 11-06-2017

Quote:

Originally Posted by WVZR-1

In that snapshot Jerry this would be GM SPO info for the spacers/collars

.396 is actually 10mm x 25.5 diameter GM# 1978064 (WAI 46-1601-1)

.232 is actually 5.8mm x 25.5 diameter GM# 1985999 (WAI 46-1617-1)

If a person were needing these the WAI information would likely be used by all after-market vendors.

You are amazing!

WVZR-1 · 11-06-2017

Knowing the dimensions of these two if you were to disassemble a CS144 for an LT5 the 3d on the rotor shaft behind the bearing would be the "other than".

conesare2seconds · 11-04-2017

Edited, somehow posted in this thread instead of the hypothetical restoration thread, oops.

11-04-2017	#1
Z51JEFF Join Date: Dec 2007 Location: Fremont,Ca Posts: 3,078	A moron needs some help. I've got a spare alternator I tore apart to rebuild now can't remember what order the 3 collars or spacers go,there are 2 that go on each side of the bearing and one between the fan and pulley. Anybody got the info on this? I've searched the net for a diagram,schematic but can't find anything. Thanks.

11-04-2017	#2
A26B Join Date: Dec 2003 Location: Arcadia,OK Posts: 3,394	Re: A moron needs some help. Scroll down in this thread for a picture http://www.zr1.net/forum/showthread.php?t=27876 __________________ Jerry Downey JERRYS LT5 GASKETS & PARTS http://www.jerrysgaskets.com 1994 *ZR-1*, Black/Black, Lingenfelter Aerobody, 416cu in, 3.91 gears, coil-over susp, Brembo brakes, etc. 2016 Black-Red, 3LT-Z51 Auto 8-speed.

11-06-2017	#6
WVZR-1 Join Date: Oct 2004 Posts: 1,890	Re: A moron needs some help. Knowing the dimensions of these two if you were to disassemble a CS144 for an LT5 the 3d on the rotor shaft behind the bearing would be the "other than".

11-04-2017	#7
conesare2seconds Join Date: Jul 2016 Location: Greater St. Louis Posts: 490	Re: A moron needs some help. Edited, somehow posted in this thread instead of the hypothetical restoration thread, oops. Last edited by conesare2seconds; 11-05-2017 at 08:11 PM.