Wipers won't wipe - ZR-1 Net Registry Forums

JRZR · 10-12-2016

I have an unusual problem with my '90 Beast (0071). When the hood is closed the driver's side wiper gets caught on the lip of the hood and can't make it to the windshield. I've tried adjusting the hood till i'm Bright Red in the face. To get it to clear, i have to adjust both sides up till it will no longer latch.

I've bought two sets of aftermarket blades, broke both of them. Went to the local Chevrolet dealer and bought what they said were the correct blades. Same result. Does anyone have any idea what's going on and how i should approach correcting this problem? Any thoughts deeply appreciated.

RussMcB · 10-12-2016

Can you post a picture, please? I think that might help.

I'm interested in this discussion. I think my wiper arms might need adjusting.

JRZR · 10-12-2016

Well, i can try. I've never posted a photo; not sure exactly how it's done. However, i'll get the car out into the sunlight and take some photos and try to post the most descriptive of the problem. I don't usually get it out if rain is forecast, so the problem is not crucial. Sometimes, however, i get caught not suspecting rain.

lfalzarano · 11-13-2016

I just checked my #1476 and the height of the driver side wiper to the windshield is 1 1/8 inches. It fits under the two stops just below the window base. The wiper blades are 19 3/4" (driverside) and 19 1/2" (passenger side). I used the original blade holders, but only replaced the rubber blades. They did bang into each other, but I bought the shorter blade on the passenger side from Chevy dealer. No problems since. Attached is a picture to compare.

Hope this helps

Mystic ZR-1 · 11-13-2016

Try a clay bar on your windshield.
It reduces drag on your wipers which often
is why your wipers hit each other or chatter.
You'll be suprised at how much better your windshield looks too... Two different size blades should not be required, unless an arm is bent
or in the unlikely event the adjustment is off.

JRZR · 11-14-2016

Thanks for the response. I did succeed in getting it corrected. Apparently, i was buying the wrong blades every time. Once I got the Trico, problem was fixed. I appreciate all the help!

10-12-2016	#2
RussMcB Join Date: Jan 2015 Location: Marietta, GA USA Posts: 1,160	Re: Wipers won't wipe Can you post a picture, please? I think that might help. I'm interested in this discussion. I think my wiper arms might need adjusting.

10-12-2016	#3
JRZR Join Date: Jun 2007 Location: Bartlett, TN Posts: 11	Re: Wipers won't wipe Well, i can try. I've never posted a photo; not sure exactly how it's done. However, i'll get the car out into the sunlight and take some photos and try to post the most descriptive of the problem. I don't usually get it out if rain is forecast, so the problem is not crucial. Sometimes, however, i get caught not suspecting rain.

11-13-2016	#5
Mystic ZR-1 Join Date: Jan 2010 Location: Mystic CT Posts: 2,633	Re: Wipers won't wipe Try a clay bar on your windshield. It reduces drag on your wipers which often is why your wipers hit each other or chatter. You'll be suprised at how much better your windshield looks too... Two different size blades should not be required, unless an arm is bent or in the unlikely event the adjustment is off.

11-14-2016	#6
JRZR Join Date: Jun 2007 Location: Bartlett, TN Posts: 11	Re: Wipers won't wipe Thanks for the response. I did succeed in getting it corrected. Apparently, i was buying the wrong blades every time. Once I got the Trico, problem was fixed. I appreciate all the help!

10-12-2016	#1
JRZR Join Date: Jun 2007 Location: Bartlett, TN Posts: 11	Wipers won't wipe I have an unusual problem with my '90 Beast (0071). When the hood is closed the driver's side wiper gets caught on the lip of the hood and can't make it to the windshield. I've tried adjusting the hood till i'm Bright Red in the face. To get it to clear, i have to adjust both sides up till it will no longer latch. I've bought two sets of aftermarket blades, broke both of them. Went to the local Chevrolet dealer and bought what they said were the correct blades. Same result. Does anyone have any idea what's going on and how i should approach correcting this problem? Any thoughts deeply appreciated.