|
|
|
04-29-2014
|
#1 |
 Join Date: Apr 2013
Location: Eastern Missouri
Posts: 773
|
Front end "Pop"
Once in awhile when turning at slow speed I will get a "pop" from I believe the right front. Not always and usually will just do it once. I have checked front end for loose stuff - and car was just State Safety Inspected, and checked over by my local shop since I still have a vibration - with nothing loose found. Any ideas? (I would assume nothing has ever been changed with 19k miles)
__________________
[LEFT][SIGPIC][/SIGPIC][/LEFT] [CENTER][COLOR=Indigo][SIZE=4][I][B] **Now Sold** 1990 ZR-1 #2093, Black on Black..[/B][/I][/SIZE][/COLOR][/CENTER] |
|
|
|
04-29-2014
|
#2 |
 
Join Date: Jan 2009
Location: Portland Oregon metro area (Washington side)
Posts: 3,207
|
Re: Front end "Pop"
Ball joint or tie rod end time.
Pretty easy stuff.
__________________
Scott  Vett owner since 1979._It's about the car and the people Last edited by scottfab; 04-29-2014 at 09:25 PM. |
|
|
|
|
04-30-2014
|
#3 |
|
Join Date: Apr 2013
Location: Eastern Missouri
Posts: 773
|
Re: Front end "Pop"
Are those parts ZR-1 specific - or regular C4? Part #'s?
__________________
[LEFT][SIGPIC][/SIGPIC][/LEFT] [CENTER][COLOR=Indigo][SIZE=4][I][B] **Now Sold** 1990 ZR-1 #2093, Black on Black..[/B][/I][/SIZE][/COLOR][/CENTER] |
|
|
|
|
04-30-2014
|
#4 | |
 
Join Date: Nov 2007
Location: Squires (near Ava MO in the Mark Twain N'tl Forest) - Missouri
Posts: 6,493
|
Re: Front end "Pop"
Quote:
__________________
Good carz, good food, good friendz = the best of timez! 90 #1202 "FBI" top end ported & relieved Cam timing by "Pete the Greek" Sans secondaries Chip & dyno tuning by Haibeck Automotive SW headers, X-pipe, MF muffs Former Secretary, ZR-1 Net Registry |
|
|
|
|
|
04-30-2014
|
#5 |
|
Join Date: May 2007
Location: Chicagoland, IL
Posts: 9,708
|
Re: Front end "Pop"
I just did all four corners w new Moog tie rods. Rock Auto is a great source.
$37 each. http://www.rockauto.com/catalog/more...058&cc=1041321
__________________
[SIGPIC][/SIGPIC]Former Membership Chairman Former ZR-1 Registry - BOD 1972 Corvette 4speed base Coupe SOLD long time ago 1984 Corvette Z-51/4+3 SOLD 1992 Corvette ZR-1 Aqua/Gray #474 SOLD 1992 Corvette ZR-1 Black Rose/Cognac #458 2014 Honda VFR Interceptor DX |
|
|
|
|
04-30-2014
|
#6 |
|
Join Date: Apr 2013
Location: Eastern Missouri
Posts: 773
|
Re: Front end "Pop"
Very cool! Will look into that later this year when my funds build back up. Nothing is loose so Its probably safe. I buy quite a bit of stuff from Rock Auto anyway - so thanks for the link!
__________________
[LEFT][SIGPIC][/SIGPIC][/LEFT] [CENTER][COLOR=Indigo][SIZE=4][I][B] **Now Sold** 1990 ZR-1 #2093, Black on Black..[/B][/I][/SIZE][/COLOR][/CENTER] |
|
|
|
|
05-01-2014
|
#7 |
 Join Date: Jun 2005
Location: CenCoast California
Posts: 899
|
Re: Front end "Pop"
While it is true that worn bushings, ball joints or tie rod ends can cause "pop" or "creaking" noises when driving at slow speeds and the steering is at or near full lock, you, also, need to look past those problems.
1) Make sure the bolts holding the two supports that run between the frame and the front crossmember are tightened to specification. 2) Make sure the bolts holding the two supports which run from the hood latch mounts down to the frame rails are tight. 3) Make sure the steering rack mounts are tight. 4) Make sure the control arm shaft mounting bolts are tight. |
|
|
|
|
05-01-2014
|
#8 |
|
Join Date: Apr 2013
Location: Eastern Missouri
Posts: 773
|
Re: Front end "Pop"
Thanks Hib! Never thought of that for sure. Will check bolts soon...
__________________
[LEFT][SIGPIC][/SIGPIC][/LEFT] [CENTER][COLOR=Indigo][SIZE=4][I][B] **Now Sold** 1990 ZR-1 #2093, Black on Black..[/B][/I][/SIZE][/COLOR][/CENTER] |
|
|
|
 |
|
|
Hybrid Mode
