|
|
|
09-27-2011
|
#1 |
 
Join Date: Mar 2010
Location: Fort Myers, FL
Posts: 343
|
Bleeder Screw Question
I want to replace the bleeder screws on my front calipers and I'm having trouble finding an exact replacement. What I've purchased from AutoZone and Corvette Central don't match -- the threads are longer for starters. Any problems using the ones from CC? Anywhere I can find originals?
Stuff like this should be simple but never is...  Thanks, John 
__________________
1992 #043, Aqua/Gray 40k miles |
|
|
|
09-27-2011
|
#2 |
 Join Date: Sep 2011
Location: montgomery tx
Posts: 65
|
Re: Bleeder Screw Question
Gm dealer is going to be your only bet. however it makes you feel any better I used the ones from autozone about two months ago and had no problems
__________________
[B]"the winner ain't the one with the fastest car its the one who refuses to lose" - Dale Earnhardt :saluting: |
|
|
|
|
09-28-2011
|
#3 |
|
Join Date: Mar 2010
Location: Fort Myers, FL
Posts: 343
|
Re: Bleeder Screw Question
Cool. I'm not a stickler for "correct" but it has to work...
__________________
1992 #043, Aqua/Gray 40k miles |
|
|
|
|
09-28-2011
|
#4 |
|
Join Date: Feb 2008
Location: Vancouver, BC
Posts: 252
|
Re: Bleeder Screw Question
John
I am in the exact same situ. Bought replacements from NAPA on Monday - they look like the corvette central ones.I did see that Corvette Specialties (I belive) had them on their site -and they looked like an exact match to original Yeah - one of mine looks just like yours.... Glenn
__________________
[SIGPIC][/SIGPIC] __________________ 1990 Corvette ZR-1 #2824 4.10's, Custom PROM, Flowmaster, Top End Port NCRS BC Chapter Last edited by gbmidyear66; 09-28-2011 at 11:47 AM. |
|
|
|
|
09-28-2011
|
#5 |
|
Join Date: Mar 2010
Location: Fort Myers, FL
Posts: 343
|
Re: Bleeder Screw Question
These appear to be the correct screws. I'll order a set and see if, in fact, they match the originals...
RAYBESTOS S23925 Brake Bleeder Screw 
__________________
1992 #043, Aqua/Gray 40k miles |
|
|
|
|
09-28-2011
|
#6 | |
|
Join Date: Sep 2011
Location: montgomery tx
Posts: 65
|
Re: Bleeder Screw Question
Quote:
__________________
[B]"the winner ain't the one with the fastest car its the one who refuses to lose" - Dale Earnhardt :saluting: |
|
|
|
|
|
09-28-2011
|
#7 |
|
Join Date: Feb 2008
Location: Vancouver, BC
Posts: 252
|
Re: Bleeder Screw Question
Corvette Specialties -CA-34165 84-99 Caliper Bleeder Valve
Appears to be the exact match if you want to go that way
__________________
[SIGPIC][/SIGPIC] __________________ 1990 Corvette ZR-1 #2824 4.10's, Custom PROM, Flowmaster, Top End Port NCRS BC Chapter |
|
|
|
|
09-28-2011
|
#8 | |
|
Join Date: Mar 2010
Location: Fort Myers, FL
Posts: 343
|
Re: Bleeder Screw Question
Quote:
__________________
1992 #043, Aqua/Gray 40k miles |
|
|
|
|
|
10-01-2011
|
#9 |
|
Join Date: Feb 2008
Location: Vancouver, BC
Posts: 252
|
Re: Bleeder Screw Question
A word of advice....
Don't use the Raybestos screws. I picked up those to replace my OEM's which where a bit banged up. Well, I simply could not bleed the caliper effectively with these screws (using my hand vacuum pump). The holes in these screw are smaller than OEM. I either got no flow, or lots of air. The stock screws worked fine.
__________________
[SIGPIC][/SIGPIC] __________________ 1990 Corvette ZR-1 #2824 4.10's, Custom PROM, Flowmaster, Top End Port NCRS BC Chapter |
|
|
|
|
10-01-2011
|
#10 |
|
Join Date: Sep 2011
Location: montgomery tx
Posts: 65
|
Re: Bleeder Screw Question
i had no problem with mine but i gravity bleed then manually finished each wheel also just re didi bais spring in the master cylinder made a hell fo a difference.
__________________
[B]"the winner ain't the one with the fastest car its the one who refuses to lose" - Dale Earnhardt :saluting: |
|
|
|
 |
|
|
Hybrid Mode
