Am I ready to install my headers? - ZR-1 Net Registry Forums

MuRCieLaGo · 03-02-2016

Ok, from now on I got:

-Exhaust manifolds gaskets
-Paul's dipstick bracket
-OBX headers
-Patience

Haven't received the headers yet though, will I need to have them surfaced?

I will also need to order a chip from Marc Haibeck.

Do I need something else? Bolts? o2 harness extension? Permatex?

Thanks!

Paul Workman · 03-02-2016

Yes. You'll need that too!

MuRCieLaGo · 03-02-2016

Paul, I'm not sure what you mean by "that".

Paul Workman · 03-02-2016

Quote:

Originally Posted by MuRCieLaGo

Paul, I'm not sure what you mean by "that".

Sorry...

. I wuz just havin fun wid ya!

=Jeff= filled in the blanks.

MuRCieLaGo · 03-02-2016

Quote:

Originally Posted by Paul Workman

Sorry...

. I wuz just havin fun wid ya!

=Jeff= filled in the blanks.

Hahaha! Jeff made it very clear.

BUT,

Will I need to surface the headers flanges? It hasn't been answered yet.

And thanks Demps for the grommet tip!

-=Jeff=- · 03-03-2016

Quote:

Originally Posted by MuRCieLaGo

Hahaha! Jeff made it very clear.

BUT,

Will I need to surface the headers flanges? It hasn't been answered yet.

And thanks Demps for the grommet tip!

I cannot answer that as I had purchased used Watson Headers and just bolted them on..

Scrrem · 03-23-2016

Quote:

Originally Posted by MuRCieLaGo

Hahaha! Jeff made it very clear.

BUT,

Will I need to surface the headers flanges? It hasn't been answered yet.

And thanks Demps for the grommet tip!

I just had to pull my header back off last week and seal with the high temp sealer that Secondchance mentioned due to leaks at the flange on both sides. When I ran a file across the flange, didn't get much contact where the tube came through the flange. So may not be a bad thing to surface the flange if you have the capability, or just use the sealer.
Rich

-=Jeff=- · 03-02-2016

Bolts - YES
O2 Extension - YES
Permatex - Always good to keep on hand

Demps · 03-02-2016

Dipstick grommet from Jerry (unless you're very careful & lucky)

Ted

secondchance · 03-02-2016

My 94 did not need O2 sensor extension. I believe OBX headers, due to fake cats, O2 sensor bungs are 3-4 inches forward compared to Stainlessworks headers.
Any other OBX header users remember different?

Also, I used Permatex high temp copper sealant per Phil's recommendation. Seems to help the seal and keep the bolts from vibrating loose. Although I used Stage 8 bolts with locking tabs, Phil's suggestion was not to use the locking tabs since header gasket tends to shrink at times necessitating re-torquing of header bolts - impossible once locking tabs are used. However, there are two bolts impossible to get to once dip stick bracket is installed. For those bolts I used the locking tabs knowing I won't be able to re-torque.

03-02-2016	#1
MuRCieLaGo Join Date: Aug 2014 Location: Trois-Rivieres (QC) Posts: 473	Am I ready to install my headers? Ok, from now on I got: -Exhaust manifolds gaskets -Paul's dipstick bracket -OBX headers -Patience Haven't received the headers yet though, will I need to have them surfaced? I will also need to order a chip from Marc Haibeck. Do I need something else? Bolts? o2 harness extension? Permatex? Thanks! Last edited by MuRCieLaGo; 03-02-2016 at 05:19 PM.

03-02-2016	#2
Paul Workman Join Date: Nov 2007 Location: Squires (near Ava MO in the Mark Twain N'tl Forest) - Missouri Posts: 6,493	Re: Am I ready to install my headers? Yes. You'll need that too! __________________ Good carz, good food, good friendz = the best of timez! 90 #1202 "FBI" top end ported & relieved Cam timing by "Pete the Greek" Sans secondaries Chip & dyno tuning by Haibeck Automotive SW headers, X-pipe, MF muffs Former Secretary, ZR-1 Net Registry

03-02-2016	#3
MuRCieLaGo Join Date: Aug 2014 Location: Trois-Rivieres (QC) Posts: 473	Re: Am I ready to install my headers? Paul, I'm not sure what you mean by "that".

03-02-2016	#8
-=Jeff=- Join Date: Jul 2007 Location: Bartlett, IL Posts: 7,161	Re: Am I ready to install my headers? Bolts - YES O2 Extension - YES Permatex - Always good to keep on hand __________________ 1990 Corvette ZR-1 #1051 Watson Headers (2" Primary) - Flowmaster Cats - Borla Catback Late Model IH - Plenum Coilovers - 4.10s Custom Interior NCM Lifetime Member #978

03-02-2016	#9
Demps Join Date: Jan 2006 Location: Niceville Posts: 997	Re: Am I ready to install my headers? Dipstick grommet from Jerry (unless you're very careful & lucky) Ted

03-02-2016	#10
secondchance Join Date: Aug 2006 Location: McLean, VA Posts: 3,721	Re: Am I ready to install my headers? My 94 did not need O2 sensor extension. I believe OBX headers, due to fake cats, O2 sensor bungs are 3-4 inches forward compared to Stainlessworks headers. Any other OBX header users remember different? Also, I used Permatex high temp copper sealant per Phil's recommendation. Seems to help the seal and keep the bolts from vibrating loose. Although I used Stage 8 bolts with locking tabs, Phil's suggestion was not to use the locking tabs since header gasket tends to shrink at times necessitating re-torquing of header bolts - impossible once locking tabs are used. However, there are two bolts impossible to get to once dip stick bracket is installed. For those bolts I used the locking tabs knowing I won't be able to re-torque. Last edited by secondchance; 03-02-2016 at 09:46 PM.