Clever bracket ideas to hold secondaries open? - ZR-1 Net Registry Forums

RussMcB · 01-26-2015

Before I start fabricating, I thought I'd check here first to see if anyone has come up with a clever simple way to hold the secondary throttle plates open.

I'm in the middle of a plenum pull and have decided to remove the secondaries. I've ordered a chip from Marc. He convinced me I don't want/need to tackle the removal of the plates and their shafts at this time, and it's easier to just make something to hold the plates open for now (and save the bigger job for a future date).

I'm assuming I'll reconnect the two linkage shafts, and make a pair of brackets to hold the linkages in the desired position.

Anyone already do this, and can save me some mental effort? It's in short supply these days.

Thank you.

XfireZ51 · 01-27-2015

Just tie wrap them open. Ran that way for 2 years w no problem. However, you'll need chip re-done. I actually removed the throttle plates.

RussMcB · 01-27-2015

Yes, thank you. I had a closer look and tie wrap or safety wire should work fine. No fancy bracket needed.

Maybe someday I'll remove the throttle plates. I agree it's the right thing to do. Certainly no reason for keeping the restriction. I'm just not ready to go that extra step at this time. I'm jonesin' to get it on the road again. Can't wait to see what it's suppose to feel like (with new coils and injectors). I should get an extra bump of performance from Marc's chip, too. Woo hoo!

RICHARD TILL · 01-27-2015

Tied my secondary actuators open with tie wire. New chip, coils and rebuilt injectors. No regrets. Wish i had cleaned the starter solenoid contacts at that time. Would have saved another plenum pull.

Paul Workman · 01-27-2015

Quote:

Originally Posted by RICHARD TILL

Tied my secondary actuators open with tie wire. New chip, coils and rebuilt injectors. No regrets. Wish i had cleaned the starter solenoid contacts at that time. Would have saved another plenum pull.

YES! Good point. My contacts were pretty much used up after 40k miles. So, for less than $10 for the pair, I replaced them while the plenum was off. (Also cleaned up the contact ring (I call it) of arching deposits: reused the original (shuttle).)

I bought mine on ebay, but since I've seen them at NAPA and I suppose they can be found elsewhere (fairly common to several cars, apparently).

RussMcB · 01-27-2015

Thanks for the starter refresh suggestions and details. I'll swing by NAPA this afternoon.

01-26-2015	#1
RussMcB Join Date: Jan 2015 Location: Marietta, GA USA Posts: 1,160	Clever bracket ideas to hold secondaries open? Before I start fabricating, I thought I'd check here first to see if anyone has come up with a clever simple way to hold the secondary throttle plates open. I'm in the middle of a plenum pull and have decided to remove the secondaries. I've ordered a chip from Marc. He convinced me I don't want/need to tackle the removal of the plates and their shafts at this time, and it's easier to just make something to hold the plates open for now (and save the bigger job for a future date). I'm assuming I'll reconnect the two linkage shafts, and make a pair of brackets to hold the linkages in the desired position. Anyone already do this, and can save me some mental effort? It's in short supply these days. Thank you. __________________ Russ McBride, [COLOR="Red"]Car Sold 8/2020[/COLOR] #1635, Marietta, GA USA, 1991 ZR-1, #766 (bought 1/1/2015) MS3-Pro, OBX, SW X-Pipe, Borla, Hurst, SLP, Goodyear F1 GS-D3, Kenwood. HOTB 2016Q3 [IMG]http://zr1.net/forum/picture.php?albumid=316&pictureid=2873[/IMG] [IMG]http://zr1.net/forum/picture.php?albumid=336&pictureid=2985[/IMG]

01-27-2015	#2
XfireZ51 Join Date: May 2007 Location: Chicagoland, IL Posts: 9,707	Re: Clever bracket ideas to hold secondaries open? Just tie wrap them open. Ran that way for 2 years w no problem. However, you'll need chip re-done. I actually removed the throttle plates. __________________ [SIGPIC][/SIGPIC]Former Membership Chairman Former ZR-1 Registry - BOD 1972 Corvette 4speed base Coupe SOLD long time ago 1984 Corvette Z-51/4+3 SOLD 1992 Corvette ZR-1 Aqua/Gray #474 SOLD 1992 Corvette ZR-1 Black Rose/Cognac #458 2014 Honda VFR Interceptor DX

01-27-2015	#3
RussMcB Join Date: Jan 2015 Location: Marietta, GA USA Posts: 1,160	Re: Clever bracket ideas to hold secondaries open? Yes, thank you. I had a closer look and tie wrap or safety wire should work fine. No fancy bracket needed. Maybe someday I'll remove the throttle plates. I agree it's the right thing to do. Certainly no reason for keeping the restriction. I'm just not ready to go that extra step at this time. I'm jonesin' to get it on the road again. Can't wait to see what it's suppose to feel like (with new coils and injectors). I should get an extra bump of performance from Marc's chip, too. Woo hoo! __________________ Russ McBride, [COLOR="Red"]Car Sold 8/2020[/COLOR] #1635, Marietta, GA USA, 1991 ZR-1, #766 (bought 1/1/2015) MS3-Pro, OBX, SW X-Pipe, Borla, Hurst, SLP, Goodyear F1 GS-D3, Kenwood. HOTB 2016Q3 [IMG]http://zr1.net/forum/picture.php?albumid=316&pictureid=2873[/IMG] [IMG]http://zr1.net/forum/picture.php?albumid=336&pictureid=2985[/IMG]

01-27-2015	#4
RICHARD TILL Join Date: Aug 2005 Location: Iuka, Mississippi 38852 Posts: 756	Re: Clever bracket ideas to hold secondaries open? Tied my secondary actuators open with tie wire. New chip, coils and rebuilt injectors. No regrets. Wish i had cleaned the starter solenoid contacts at that time. Would have saved another plenum pull.

01-27-2015	#6
RussMcB Join Date: Jan 2015 Location: Marietta, GA USA Posts: 1,160	Re: Clever bracket ideas to hold secondaries open? Thanks for the starter refresh suggestions and details. I'll swing by NAPA this afternoon. __________________ Russ McBride, [COLOR="Red"]Car Sold 8/2020[/COLOR] #1635, Marietta, GA USA, 1991 ZR-1, #766 (bought 1/1/2015) MS3-Pro, OBX, SW X-Pipe, Borla, Hurst, SLP, Goodyear F1 GS-D3, Kenwood. HOTB 2016Q3 [IMG]http://zr1.net/forum/picture.php?albumid=316&pictureid=2873[/IMG] [IMG]http://zr1.net/forum/picture.php?albumid=336&pictureid=2985[/IMG]