|
![]() |
#1 |
![]() Join Date: May 2007
Location: Westminster, Maryland
Posts: 3,687
|
![]()
I need the door glass guide for passenger side glass.
This guide (a plastic piece) attaches to the lower, forward corner of the glass and rides on the guide bar to position the glass properly as it is raised. My guide is broken and the glass goes too far up and then the upper rear corner of the glass hits the edge of the halo when the door is closed. I believe that the part I need is not year specific, and it is not ZR-1 only. Anybody got one? Jim 443-244-1347
__________________
If it isn't fun, you aren't doing it right! 1990 Black ZR-1 - sold 1993 Quasar Blue ZR-1 1994 Competition Yellow ZR-1 1995 Dark Purple ZR-1 Maryland State Coordinator WAZOO Member |
![]() |
![]() |
![]() |
#2 |
![]() Join Date: Apr 2007
Location: Northern VA
Posts: 2,655
|
![]()
Jim,
I just did this repair on my driver side window. Found the the guide on ebay.
__________________
Phil Wasinger 1994 Torch Red ZR-1 WAZOO Member George Braml Intake |
![]() |
![]() |
![]() |
#3 |
![]() Join Date: Apr 2007
Location: Northern VA
Posts: 2,655
|
![]()
Here you go
Right side: http://www.ebay.com/itm/1992-thru-19...#ht_2736wt_868 Left side: http://www.ebay.com/itm/1992-thru-19...#ht_2893wt_868
__________________
Phil Wasinger 1994 Torch Red ZR-1 WAZOO Member George Braml Intake Last edited by Jagdpanzer; 07-31-2014 at 03:07 PM. |
![]() |
![]() |
![]() |
#4 |
![]() Join Date: May 2007
Location: Westminster, Maryland
Posts: 3,687
|
![]()
Thanks Phil. I thought it was too obscure a part for eBay. Silly me.
Bought it!! Jim
__________________
If it isn't fun, you aren't doing it right! 1990 Black ZR-1 - sold 1993 Quasar Blue ZR-1 1994 Competition Yellow ZR-1 1995 Dark Purple ZR-1 Maryland State Coordinator WAZOO Member |
![]() |
![]() |
![]() |
#5 |
![]() Join Date: Sep 2012
Location: Rockwall, Tx
Posts: 1,510
|
![]()
Jim, I just did this repair as well. You're going to have fun with the nut that holds that stop/guide on. The back side is basically a big washer with 2 opposing holes and you have to either buy the tool ($65) or improvise. I used a set of 90 degree needle nose pliers. It is very tight and has thread locker on it. That was the most difficult part of the install. The only difficult part actually.
__________________
_________________ 1994 AB/Grey #141 430 RWHP/392 RWTQ FBI Lyposuction / Secondaries relieved of duty / SW Long Tube Headers / Corsa Exhaust / FIC SS Injectors / MSD Coils / Lightweight Pulleys / Corey tuned B & M Shifter / Aluminum Flywheel / Samco Hoses / Shelby Series One's / C4 No Flex Frame Stiffener BBC - Bling By Carter: Custom ZR-1 Center Caps / Custom Plenum Plate / Air Box Knobs / TB Cover / Oil Filter Cover |
![]() |
![]() |
![]() |
#6 |
![]() ![]() ![]() Join Date: May 2007
Location: Peoria, AZ
Posts: 9,154
|
![]()
Does anybody know if these will work on a 90 or 91? I know it was an improvement for all MY92s and up because of the rattle glass problems in 90and 91 when the windows are down. Anybody has this mod or done this yet? I dont think so im not sure if the 90s and 91s have the rod guide that holds this stop in the window, nor the hole in the window where the guide stop goes? Phil ??/ Anybody please advise -=JEFF=- ?
Note to JIM I think I have this specific socket with the two tines on it. LMK if you like to borrow it? Also Jim great pics below of the work details. GC http://forums.corvetteforum.com/c4-t...indow-fix.html
__________________
GOLDCYLON - 91 ZR-1 #2014 GOLDCYLON - 90 ZR-1 #2794, 4L60e (Formerly Schrade's) GOLDCYLON - 11 CTS-V Arizona State Director ![]() 91 WHITE/BLACK #2014. 380 P&P&PCed,Ported Heads, Jeal Long tubes, Corsa Exhaust/FIKSE FM-5s /LED TLs, LED Headlights, Front Wilwood 6 piston narrowlite calipers and rear Wilwood caliper street shop mod,CNCed Coolant Pipes,TPI Cvr,Filter cover,Stainless Bolts, DRM/DOM PROM /ZFDOC mod build #102,DRLs,BMAD with stainless Debris Screen,Coplan Air Blaster, Pioneer APP Radio 4,Brey-Krause HB,Sub Bar,Fire extinguisher seat mount,DRM Coilovers,LEDs everywhere,Compass mirror (orange),V1 DIC hidden display, Homelink sun visor, Carbon Fiber top x3 and APSIS Carbon Fiber interior, APSIS CF Steering Wheel/NAPA Leather, Banski trailing arms, Guldstrand front suspension,urethane bushings from Prothane (total suspension) ZFDoc drive shaft safety loop, raptor shift light (orange),AO engineering louver front plate, Console seat cushion, 96CE seats with black custom Sheepskins, ss billet catch can,Viper remote entry/alarm,Cragar Rear Louvers,LED side louver lights, Dewitts Radiator with SPAL fans and a Woods 160 T-Stat 90 RED/BLACK #2794. 4L60e Automatic Stage V by RPM Transmission, TCI Dedicated TCM, OBX Stainless Headers, Corsa Exhaust, SAN Secondaries and Haibeck PROM, Exotic Muscle Coil overs, LED Interior Lights, LED Tail Lights, LED Headlights, 94 Sport seats with black custom Sheepskins , Cragar rear louvers, GS Front calipers, Banski Trailing arms, APSIS Carbon Fiber steering wheel, Front and Rear Baer Eradispeeds, DRLs, Guldstrand front suspension,urethane bushings from Prothane (total suspension), Dewitt's Raditor with Dual SPAL fans and a Haibeck 170 T-Stat 11 RED/GREY CTS-V Last edited by GOLDCYLON; 08-01-2014 at 08:57 AM. |
![]() |
![]() |
![]() |
#7 |
![]() Join Date: Sep 2012
Location: Rockwall, Tx
Posts: 1,510
|
![]()
Jim - If the tool is available I would def use it. It can be done without it but that spanner nut is so tight with the thread lock it can be very frustrating. Just my .02 worth...
GC, if I decide to do my passenger side while it's fresh in my mind do you mind a quick loan of the socket?
__________________
_________________ 1994 AB/Grey #141 430 RWHP/392 RWTQ FBI Lyposuction / Secondaries relieved of duty / SW Long Tube Headers / Corsa Exhaust / FIC SS Injectors / MSD Coils / Lightweight Pulleys / Corey tuned B & M Shifter / Aluminum Flywheel / Samco Hoses / Shelby Series One's / C4 No Flex Frame Stiffener BBC - Bling By Carter: Custom ZR-1 Center Caps / Custom Plenum Plate / Air Box Knobs / TB Cover / Oil Filter Cover |
![]() |
![]() |
![]() |
#8 | |
![]() ![]() ![]() Join Date: May 2007
Location: Peoria, AZ
Posts: 9,154
|
![]() Quote:
__________________
GOLDCYLON - 91 ZR-1 #2014 GOLDCYLON - 90 ZR-1 #2794, 4L60e (Formerly Schrade's) GOLDCYLON - 11 CTS-V Arizona State Director ![]() 91 WHITE/BLACK #2014. 380 P&P&PCed,Ported Heads, Jeal Long tubes, Corsa Exhaust/FIKSE FM-5s /LED TLs, LED Headlights, Front Wilwood 6 piston narrowlite calipers and rear Wilwood caliper street shop mod,CNCed Coolant Pipes,TPI Cvr,Filter cover,Stainless Bolts, DRM/DOM PROM /ZFDOC mod build #102,DRLs,BMAD with stainless Debris Screen,Coplan Air Blaster, Pioneer APP Radio 4,Brey-Krause HB,Sub Bar,Fire extinguisher seat mount,DRM Coilovers,LEDs everywhere,Compass mirror (orange),V1 DIC hidden display, Homelink sun visor, Carbon Fiber top x3 and APSIS Carbon Fiber interior, APSIS CF Steering Wheel/NAPA Leather, Banski trailing arms, Guldstrand front suspension,urethane bushings from Prothane (total suspension) ZFDoc drive shaft safety loop, raptor shift light (orange),AO engineering louver front plate, Console seat cushion, 96CE seats with black custom Sheepskins, ss billet catch can,Viper remote entry/alarm,Cragar Rear Louvers,LED side louver lights, Dewitts Radiator with SPAL fans and a Woods 160 T-Stat 90 RED/BLACK #2794. 4L60e Automatic Stage V by RPM Transmission, TCI Dedicated TCM, OBX Stainless Headers, Corsa Exhaust, SAN Secondaries and Haibeck PROM, Exotic Muscle Coil overs, LED Interior Lights, LED Tail Lights, LED Headlights, 94 Sport seats with black custom Sheepskins , Cragar rear louvers, GS Front calipers, Banski Trailing arms, APSIS Carbon Fiber steering wheel, Front and Rear Baer Eradispeeds, DRLs, Guldstrand front suspension,urethane bushings from Prothane (total suspension), Dewitt's Raditor with Dual SPAL fans and a Haibeck 170 T-Stat 11 RED/GREY CTS-V |
|
![]() |
![]() |
![]() |
#9 |
![]() Join Date: Oct 2004
Posts: 1,889
|
![]()
I messaged Dan (Y-ME) and he mentions having likely a '94 glass as well as an earlier than '90 glass so he's going to lay them one on another and compare the holes. I read that the holes were changed many years ago but I'm not so sure, he can confirm. '90 and earlier glass is SoftRay, '91 is EZKool and it would be interesting to know what the '93+ door glass were. Were there actually changes physically to the glass or just the tint and maybe the sourcing. Anyone with a '94 or '95 want to confirm the branding on the door glass 'bug'?
If the glass matches then if a person cannibalized some '93+ doors for the guides then all years could be updated. |
![]() |
![]() |
![]() |
#10 |
![]() Join Date: Mar 2014
Location: Warrington PA
Posts: 1,913
|
![]()
Funny I checked this thread out tonight, as we had the ZR-1 out for dinner earlier, and I noticed the exact thing that is mentioned here is happening to my RS door glass, leaving a mark on the halo.......now I know how to correct the problem.....great info.....
![]()
__________________
Tom 1994 ZR-1 #009 "captured test fleet car" 1974 LS4 454 Vert 1982 L83 CFI...now a retired "dd"....Sold WAZOO Member |
![]() |
![]() |
![]() |
|
|