Crank No-Start/Idle 91 ZR-1 - ZR-1 Net Registry Forums

BaggyToaster · 09-20-2024

Hello everyone, I have been a long time reader of these forums and the information has been quite helpful. I have a 91 ZR-1 that has been plaguing my existence. I first diagnosed a crank no start as a bad ECM due to lack of injector pulse and continuity to ground through ECM when cranking. Had the ECM rebuilt and the thing started right up and ran like a top for 3 days. On the 4th day I shut the vehicle off and when I went to restart it, it died instantly. I have initial injector pulse for cold start key on for all injectors. It cranks, fires off of initial pulse fuel, then dies within 2 seconds. I have good spark at all plugs, good cam and crank sensors with good continuity to ignition control module. The only thing i am losing is injector pulse once cranking. I have no ECM or CCM codes. Could the ECM have gone belly up again? I have hit a wall and would appreciate any feed back or additional diagnostic routes that I have not explored. I have a FSM for the vehicle as well.

Marc Haibeck · 09-22-2024

Try these two suggestions.

Is there a VATS lockout? With the door open and the ignition key off the Security light should be blinking. Close the door and try to start the engine. Is the Security light off when you have the ignition key on?

Observe the fuel pressure when the engine is cranking and not firing. The fuel pressure must be over 30 psi for the engine to fire. What is the fuel pressure while cranking?

Marc

BaggyToaster · 09-22-2024

Security light flashes normally. Key in and ignition on, security light goes out. Starter cranks normally but engine will not continue to run. Fuel pressure is good and does not fluctuate while cranking.

Marc Haibeck · 09-23-2024

The future of your ECM is not looking good. Maybe it has a poor internal connection. Have someone bang on the ECM with their hand while you are cranking the engine. Beyond that, try to find another ZR-1 that you can swap ECM's with to confirm the defective ECM.

Marc

BaggyToaster · 09-23-2024

I will give that a shot. Don't know of any other C4 LT5s in the area but I will be on the lookout. We had the ECM rebuilt so it has a warranty. Thank you very much for the help.

Corvette95 · 09-23-2024

May I ask who rebuilt the ECM?

BaggyToaster · 10-01-2024

ZR1ecm.com. Sorry I was away for a few days.

Corvette95 · 10-02-2024

Quote:

Originally Posted by BaggyToaster

ZR1ecm.com. Sorry I was away for a few days.

Thanks. Never heard of them but if they CAN truely fix a ZR-1 ECM that would be wonderful. Your experience with make makes them look kinda shady.

Dynomite · 1 Week Ago

Sounds like zr1ecm.com (Macroblock) can fix ZR1 ECMs 👍

ECMs with some solder bridges on the original boards cracked, and some broken.

BaggyToaster · 10-02-2024

I wouldn't label them shady quite yet. We have been in communication with them and so far they have tried to help resolve the issue. The rebuild did come with a warranty. All we can do is give them a chance to fix the issue if it is in-fact a defective ECM. I have a couple more advanced diag steps to try. I am going to try to mimic a crank signal from the Ignition module to the ECM to see if I get injector pulse, if that does not show results the ECM is definitively the issue. I will do my best to update.

09-20-2024	#1
BaggyToaster Join Date: Sep 2024 Location: NEVADA Posts: 8	Crank No-Start/Idle 91 ZR-1 Hello everyone, I have been a long time reader of these forums and the information has been quite helpful. I have a 91 ZR-1 that has been plaguing my existence. I first diagnosed a crank no start as a bad ECM due to lack of injector pulse and continuity to ground through ECM when cranking. Had the ECM rebuilt and the thing started right up and ran like a top for 3 days. On the 4th day I shut the vehicle off and when I went to restart it, it died instantly. I have initial injector pulse for cold start key on for all injectors. It cranks, fires off of initial pulse fuel, then dies within 2 seconds. I have good spark at all plugs, good cam and crank sensors with good continuity to ignition control module. The only thing i am losing is injector pulse once cranking. I have no ECM or CCM codes. Could the ECM have gone belly up again? I have hit a wall and would appreciate any feed back or additional diagnostic routes that I have not explored. I have a FSM for the vehicle as well.

09-22-2024	#2
Marc Haibeck Join Date: May 2007 Location: Addison IL Posts: 250	Re: Crank No-Start/Idle 91 ZR-1 Try these two suggestions. Is there a VATS lockout? With the door open and the ignition key off the Security light should be blinking. Close the door and try to start the engine. Is the Security light off when you have the ignition key on? Observe the fuel pressure when the engine is cranking and not firing. The fuel pressure must be over 30 psi for the engine to fire. What is the fuel pressure while cranking? Marc

09-22-2024	#3
BaggyToaster Join Date: Sep 2024 Location: NEVADA Posts: 8	Re: Crank No-Start/Idle 91 ZR-1 Security light flashes normally. Key in and ignition on, security light goes out. Starter cranks normally but engine will not continue to run. Fuel pressure is good and does not fluctuate while cranking.

09-23-2024	#4
Marc Haibeck Join Date: May 2007 Location: Addison IL Posts: 250	Re: Crank No-Start/Idle 91 ZR-1 The future of your ECM is not looking good. Maybe it has a poor internal connection. Have someone bang on the ECM with their hand while you are cranking the engine. Beyond that, try to find another ZR-1 that you can swap ECM's with to confirm the defective ECM. Marc

09-23-2024	#5
BaggyToaster Join Date: Sep 2024 Location: NEVADA Posts: 8	Re: Crank No-Start/Idle 91 ZR-1 I will give that a shot. Don't know of any other C4 LT5s in the area but I will be on the lookout. We had the ECM rebuilt so it has a warranty. Thank you very much for the help.

09-23-2024	#6
Corvette95 Join Date: Jan 2006 Location: Decatur, AL Posts: 1,120	Re: Crank No-Start/Idle 91 ZR-1 May I ask who rebuilt the ECM? __________________ Corvette95 Registry and Forum (*************) 1989 C4 Conv Wht/Gry Auto Hardtop Top Flight SOLD 1995 C4 Coupe Purple/Blk 6 Speed 1989 C4 Conv Wht/Red Auto SOLD 1996 C4 Conv Black/Tan Auto SOLD 1994 C4 Coupe Wht/Blk SOLD 1995 C4 ZR-1 White/Gry #278 Dual Dunn Head SOLD 1986 C4 Coupe Black/Red 4+3 SOLD 1990 C4 ZR-1 Red/Red #0454

10-01-2024	#7
BaggyToaster Join Date: Sep 2024 Location: NEVADA Posts: 8	Re: Crank No-Start/Idle 91 ZR-1 ZR1ecm.com. Sorry I was away for a few days.

1 Week Ago	#9
Dynomite Join Date: Aug 2009 Location: South Dakota/California Posts: 3,809	Re: Crank No-Start/Idle 91 ZR-1 Sounds like zr1ecm.com (Macroblock) can fix ZR1 ECMs 👍 ECMs with some solder bridges on the original boards cracked, and some broken. __________________ Left Clickable links -Solutions- LT5 Modifications/Rebuild Tricks Low Mileage ZR-1 Restoration 1990 Corvette (L98) Modifications LT5 Eliminated Systems LT5 Added Systems LT5/ZR-1 Fluids 1995 LT5 SPECIFIC TOP END REBUILD TRICKS Last edited by Dynomite; 6 Days Ago at 09:36 PM.

10-02-2024	#10
BaggyToaster Join Date: Sep 2024 Location: NEVADA Posts: 8	Re: Crank No-Start/Idle 91 ZR-1 I wouldn't label them shady quite yet. We have been in communication with them and so far they have tried to help resolve the issue. The rebuild did come with a warranty. All we can do is give them a chance to fix the issue if it is in-fact a defective ECM. I have a couple more advanced diag steps to try. I am going to try to mimic a crank signal from the Ignition module to the ECM to see if I get injector pulse, if that does not show results the ECM is definitively the issue. I will do my best to update.