A missing nut - ZR-1 Net Registry Forums

secondchance · 10-08-2009

Hi all,

I am missing a black nut, possibly 4mm?, that holds aluminum shield/trim over the throttle pulley.
Does anyone have a spare I could buy?

Thanks.

bdw18_123 · 10-08-2009

Funny, I need those too, plus the screw that attaches it to the airhorn.

Jagdpanzer · 10-08-2009

I was also missing one of these nuts but luckily found it stuck in the inlet of engine valley drain tube when titivating under the plenum last year. I can't tell you how surprised and gratified I was when I discovered it was the missing nut as I had been searching for one to no avail since I first bought car. When I first looked in the valley after removing the starter I said to myself damn what a skimpy drain hole they put in here however, after poking around on it a bit with a pointed mettle scribe to help it drain better out popped the missing nut. And boy was I relieved that drain tube turned out to be much larger than it first appeared.
May you also have similar luck in you hunt

secondchance · 10-08-2009

Quote:

Originally Posted by Jagdpanzer

I was also missing one of these nuts but luckily found it stuck in the inlet of engine valley drain tube when titivating under the plenum last year. I can't tell you how surprised and gratified I was when I discovered it was the missing nut as I had been searching for one to no avail since I first bought car. When I first looked in the valley after removing the starter I said to myself damn what a skimpy drain hole they put in here however, after poking around on it a bit with a pointed mettle scribe to help it drain better out popped the missing nut. And boy was I relieved that drain tube turned out to be much larger than it first appeared.
May you also have similar luck in you hunt

No, Phil. I don't want to pull the freaking plenum again for a while!!!
Thanks for the well wish though.

-=Jeff=- · 10-08-2009

Quote:

Originally Posted by secondchance

Hi all,

I am missing a black nut, possibly 4mm?, that holds aluminum shield/trim over the throttle pulley.
Does anyone have a spare I could buy?

Thanks.

I don't think I have it but I can look..

QB93Z · 10-12-2009

I discovered that I need one of these nuts also. If you find a source, please let me know.

Jim

secondchance · 10-12-2009

Quote:

Originally Posted by QB93Z

I discovered that I need one of these nuts also. If you find a source, please let me know.

Jim

Jim,

It's not identical but while looking, if you go to Home Depot their hardware, bolts and nuts section, look for 4mm-7 nut is the same thread.

rhipsher · 10-12-2009

Quote:

Originally Posted by secondchance

Jim,

It's not identical but while looking, if you go to Home Depot their hardware, bolts and nuts section, look for 4mm-7 nut is the same thread.

Fastenal has just about everything.

-=Jeff=- · 10-12-2009

I know I 'had' two.. but cannot find them at the moment..

VetteMed · 10-12-2009

Quote:

Originally Posted by -=Jeff=-

I know I 'had' two.. but cannot find them at the moment..

Married?

10-08-2009	#1
secondchance Join Date: Aug 2006 Location: McLean, VA Posts: 3,723	A missing nut Hi all, I am missing a black nut, possibly 4mm?, that holds aluminum shield/trim over the throttle pulley. Does anyone have a spare I could buy? Thanks.

10-08-2009	#2
bdw18_123 Join Date: Apr 2009 Location: Prather, CA Posts: 809	Re: A missing nut Funny, I need those too, plus the screw that attaches it to the airhorn. __________________ [IMG]http://i13.photobucket.com/albums/a292/bdw18_123/_zr1netforumsigphoto.jpg[/IMG][B] 1990 Corvette ZR-1 [/B][I] White/Flame Red, #2299, mostly stock, 144K miles.[/I] -Cams timed to the '93-'95 405HP LT5 stock timing. -IAT sensor relocated to below front bumper. -Haibeck hoops installed in airduct. -OBX cat-back exhaust. [COLOR=DarkRed][B](SOLD - December 2012 [/B][/COLOR][COLOR=DarkRed][B]:hello:)[/B][/COLOR] 1993 Corvette Coupe Black/Black, 6-speed (SOLD - October 2009 :hello:)

10-08-2009	#3
Jagdpanzer Join Date: Apr 2007 Location: Northern VA Posts: 2,661	Re: A missing nut I was also missing one of these nuts but luckily found it stuck in the inlet of engine valley drain tube when titivating under the plenum last year. I can't tell you how surprised and gratified I was when I discovered it was the missing nut as I had been searching for one to no avail since I first bought car. When I first looked in the valley after removing the starter I said to myself damn what a skimpy drain hole they put in here however, after poking around on it a bit with a pointed mettle scribe to help it drain better out popped the missing nut. And boy was I relieved that drain tube turned out to be much larger than it first appeared. May you also have similar luck in you hunt

10-12-2009	#6
QB93Z Join Date: May 2007 Location: Westminster, Maryland Posts: 3,689	Re: A missing nut I discovered that I need one of these nuts also. If you find a source, please let me know. Jim __________________ If it isn't fun, you aren't doing it right! 1990 Black ZR-1 - sold 1993 Quasar Blue ZR-1 1994 Competition Yellow ZR-1 1995 Dark Purple ZR-1 Maryland State Coordinator WAZOO Member

10-12-2009	#9
-=Jeff=- Join Date: Jul 2007 Location: Bartlett, IL Posts: 7,169	Re: A missing nut I know I 'had' two.. but cannot find them at the moment.. __________________ 1990 Corvette ZR-1 #1051 Watson Headers (2" Primary) - Flowmaster Cats - Borla Catback Late Model IH - Plenum Coilovers - 4.10s Custom Interior NCM Lifetime Member #978

Thread Tools
Show Printable Version Email this Page
Display Modes
Switch to Linear Mode Hybrid Mode Switch to Threaded Mode