|
|
|
02-12-2008
|
#1 |
 
Join Date: Nov 2007
Location: Sunshine State
Posts: 1,071
|
Brake booster ?
So, I'm bored and have nothing else to do, so I decided to pull the battery out and do a little checking around....I found the cruise control hose was severely pinched and deteriorating pretty bad amazes me that the cruise worked....I followed it back inside the car & pulled it out.
Upon doing so, I noticed the boot on the booster looked a little dampened. I touched it and its brake fluid. Its not dripping or wet, just looks shiney on the bottom. Do I need to replace it immediately or can I hold off for a while?
__________________
[B]1990 #2815[/B] [COLOR="Red"][B]Red/Red[/B][/COLOR] Ported Plenum & IH (by Pete) Haibeck Chip Rebuilt FPR (by Phil) FIC Injectors Watson LT Headers 3" Stainless Works exhaust Lingenfelter Open Air Lid Bill B Built Transmission Shifter & C Beam Plates [FONT=Impact][COLOR=red]1992 [COLOR=black]#[/COLOR] 091[/COLOR][/FONT] [FONT=Impact][COLOR=#ff0000]Red/[COLOR=silver]Gray[/COLOR][/COLOR][/FONT] [B]SOLD[/B] |
|
|
|
02-13-2008
|
#2 |
|
Guest
Posts: n/a
|
Re: Brake booster ?
Que?
Is the fluid on the booster external or internal? |
|
|
|
02-13-2008
|
#3 |
|
Join Date: Nov 2007
Location: Sunshine State
Posts: 1,071
|
Re: Brake booster ?
Inside the car, looking up at the brake pedal. The rod that is linked to the pedal, which pushes inward when you press the brake......theres a boot that surrounds it...the boot is a little wet.
__________________
[B]1990 #2815[/B] [COLOR="Red"][B]Red/Red[/B][/COLOR] Ported Plenum & IH (by Pete) Haibeck Chip Rebuilt FPR (by Phil) FIC Injectors Watson LT Headers 3" Stainless Works exhaust Lingenfelter Open Air Lid Bill B Built Transmission Shifter & C Beam Plates [FONT=Impact][COLOR=red]1992 [COLOR=black]#[/COLOR] 091[/COLOR][/FONT] [FONT=Impact][COLOR=#ff0000]Red/[COLOR=silver]Gray[/COLOR][/COLOR][/FONT] [B]SOLD[/B] |
|
|
|
|
02-13-2008
|
#4 |
|
Guest
Posts: n/a
|
Re: Brake booster ?
Sounds like the master cylinder is leaking. Pull the brake master off and check to make sure it is not leaking into the booster.
|
|
|
|
02-13-2008
|
#5 |
|
Join Date: Nov 2007
Location: Sunshine State
Posts: 1,071
|
Re: Brake booster ?
Uh oh!!
__________________
[B]1990 #2815[/B] [COLOR="Red"][B]Red/Red[/B][/COLOR] Ported Plenum & IH (by Pete) Haibeck Chip Rebuilt FPR (by Phil) FIC Injectors Watson LT Headers 3" Stainless Works exhaust Lingenfelter Open Air Lid Bill B Built Transmission Shifter & C Beam Plates [FONT=Impact][COLOR=red]1992 [COLOR=black]#[/COLOR] 091[/COLOR][/FONT] [FONT=Impact][COLOR=#ff0000]Red/[COLOR=silver]Gray[/COLOR][/COLOR][/FONT] [B]SOLD[/B] |
|
|
|
|
02-15-2008
|
#6 |
|
Join Date: Nov 2007
Location: Sunshine State
Posts: 1,071
|
Re: Brake booster ?
Holy Crap!!1 $407. for a master...and thats from Tom Henry!!
__________________
[B]1990 #2815[/B] [COLOR="Red"][B]Red/Red[/B][/COLOR] Ported Plenum & IH (by Pete) Haibeck Chip Rebuilt FPR (by Phil) FIC Injectors Watson LT Headers 3" Stainless Works exhaust Lingenfelter Open Air Lid Bill B Built Transmission Shifter & C Beam Plates [FONT=Impact][COLOR=red]1992 [COLOR=black]#[/COLOR] 091[/COLOR][/FONT] [FONT=Impact][COLOR=#ff0000]Red/[COLOR=silver]Gray[/COLOR][/COLOR][/FONT] [B]SOLD[/B] |
|
|
|
 |
| Thread Tools | |
| Display Modes | |
|
|
Hybrid Mode
