Drivetrain rattle - ZR-1 Net Registry Forums

crazyb1 · 12-15-2006

I started my Z and immediately got a rattle that sounds similar to an A/C bearing going out. I turned A/C off and rattle remained. I listened from under the car and the noise is louder there (like it's coming from the headers). Pushing in the clutch changes the pitch of the rattle very slightly. The engine doesn't seem down on hp. and runs as smoothly as before. When increasing rpm, it doesn't seem (I may be wrong) that the rattle increases in pitch, volume, etc. I've thought about the alternator, A/C, and now the ZF as the culprit. 50K miles. Any ideas?

Sgreg · 12-15-2006

I think I would check the exhaust system including heat shieds all the way back. When a little loose, these items can cause a bunch of noise particularly under the car. Less likely but worth a look are engine mounts. Good luck.

guinnessdood · 12-15-2006

Quote:

Originally Posted by crazyb1

I started my Z and immediately got a rattle that sounds similar to an A/C bearing going out. I turned A/C off and rattle remained. I listened from under the car and the noise is louder there (like it's coming from the headers). Pushing in the clutch changes the pitch of the rattle very slightly. The engine doesn't seem down on hp. and runs as smoothly as before. When increasing rpm, it doesn't seem (I may be wrong) that the rattle increases in pitch, volume, etc. I've thought about the alternator, A/C, and now the ZF as the culprit. 50K miles. Any ideas?

Sounds like it could be the pilot bearing. Contact Bill Boudreau and descrieb the sound or record the sound and send it to him. www.zfdoc.com is his website...Great Guy!

crazyb1 · 12-15-2006

After listening to the motor again, the sound is more of a tapping/clicking sound, not like something is loose (rattling). If this is the heat shield, what should I be looking for? Loose fitting? Will the pilot bearing make a tapping/ticking noise if going out?

Sgreg · 12-15-2006

When I have had a pilot bearing problem , it squealed badly like a slipping fan belt. I wouldn't call it a rattle or clicking sound.. Clicking and tapping noise could be a lifter but if it's coming from underneath the car still sounds like a loose piece of exhaust. The pulsing of an exhaust causes quite a bit of vibration if everything is not secured well.

tccrab · 12-15-2006

Bearings typically don't make a tap or a rattle sound.
They squeal.
Could it be this?
http://www.zr1netregistry.com/forum/...ead.php?t=2294

For your sake, I hope not...

Make a recording of the sound and let us give it a listen.
Here's hoping it's something simple...

TomC
'90ZR1 #792

Belsy · 12-16-2006

Could it be your cat converters? They can break loose inside I believe.

Sgreg · 12-16-2006

As long as we are guessing, how about the pressure plate or throw-out bearing ?

Very hard to diagnose without being there.

12-15-2006	#1
crazyb1 Join Date: Jul 2005 Location: Star, Idaho Posts: 56	Drivetrain rattle I started my Z and immediately got a rattle that sounds similar to an A/C bearing going out. I turned A/C off and rattle remained. I listened from under the car and the noise is louder there (like it's coming from the headers). Pushing in the clutch changes the pitch of the rattle very slightly. The engine doesn't seem down on hp. and runs as smoothly as before. When increasing rpm, it doesn't seem (I may be wrong) that the rattle increases in pitch, volume, etc. I've thought about the alternator, A/C, and now the ZF as the culprit. 50K miles. Any ideas? __________________ '90 ZR-1 Red/Red #1239 SGC P/P Plenum/IH, Headers, B & B, Hurst, K & N "Red RocketShip!"

12-15-2006	#2
Sgreg Join Date: Aug 2006 Location: Texas Posts: 518	Re: Drivetrain rattle I think I would check the exhaust system including heat shieds all the way back. When a little loose, these items can cause a bunch of noise particularly under the car. Less likely but worth a look are engine mounts. Good luck. __________________ 1991 ZR-1, Black, Black, # 541

12-15-2006	#4
crazyb1 Join Date: Jul 2005 Location: Star, Idaho Posts: 56	Re: Drivetrain rattle After listening to the motor again, the sound is more of a tapping/clicking sound, not like something is loose (rattling). If this is the heat shield, what should I be looking for? Loose fitting? Will the pilot bearing make a tapping/ticking noise if going out? __________________ '90 ZR-1 Red/Red #1239 SGC P/P Plenum/IH, Headers, B & B, Hurst, K & N "Red RocketShip!"

12-15-2006	#5
Sgreg Join Date: Aug 2006 Location: Texas Posts: 518	Re: Drivetrain rattle When I have had a pilot bearing problem , it squealed badly like a slipping fan belt. I wouldn't call it a rattle or clicking sound.. Clicking and tapping noise could be a lifter but if it's coming from underneath the car still sounds like a loose piece of exhaust. The pulsing of an exhaust causes quite a bit of vibration if everything is not secured well. __________________ 1991 ZR-1, Black, Black, # 541

12-15-2006	#6
tccrab Join Date: Oct 2004 Location: Folsom CA Posts: 1,656	Re: Drivetrain rattle Bearings typically don't make a tap or a rattle sound. They squeal. Could it be this? http://www.zr1netregistry.com/forum/...ead.php?t=2294 For your sake, I hope not... Make a recording of the sound and let us give it a listen. Here's hoping it's something simple... TomC '90ZR1 #792 __________________ TomC '90ZR1 #792 Honorary Pirate [B]If it ain't FUN, you're doing something terribly WRONG. [/B]

12-16-2006	#7
Belsy Join Date: Nov 2006 Location: DeBary , Fl. Posts: 119	Re: Drivetrain rattle Could it be your cat converters? They can break loose inside I believe.

12-16-2006	#8
Sgreg Join Date: Aug 2006 Location: Texas Posts: 518	Re: Drivetrain rattle As long as we are guessing, how about the pressure plate or throw-out bearing ? Very hard to diagnose without being there. __________________ 1991 ZR-1, Black, Black, # 541

Thread Tools
Show Printable Version Email this Page
Display Modes
Switch to Linear Mode Hybrid Mode Switch to Threaded Mode