|
|
|
10-04-2006
|
#1 |
Join Date: Sep 2006
Location: Little Rock, Arkansas
Posts: 35
|
No reverse lights
No Reverse lights, fuse is good,
switch in/on trans, and where ? |
|
|
|
10-04-2006
|
#2 |
|
Guest
Posts: n/a
|
Re: No reverse lights
Switch is on the trans driver side, upper half of the motor. Check continuity at the switch.
Also contact www.zfdoc.com |
|
|
|
10-04-2006
|
#3 | |
 
Join Date: Oct 2004
Location: Woods Cross, UT
Posts: 389
|
Re: No reverse lights
Quote:
__________________
Uly Past OWNER 90 ZR-1 #0120 Red/Saddle UT Plate: EZR1DER |
|
|
|
|
|
10-04-2006
|
#4 | |
|
Join Date: Feb 2004
Location: Ma
Posts: 404
|
Re: No reverse lights
Quote:
__________________
1990 ZR1 #2574 Medium Quasar Blue Metallic 1 of 19 |
|
|
|
|
|
10-04-2006
|
#5 |
Join Date: May 2005
Location: Leesburg, VA
Posts: 2,713
|
Re: No reverse lights
I borrowed a tool from Bill B that made it much, much easier. I think he charged like $5 for rental plus shipping.
__________________
Bob Saveland Former owner of #2517 [IMG]http://a.random-image.net/aurora40/vette.jpg[/img] |
|
|
|
|
10-05-2006
|
#6 |
|
Join Date: Sep 2006
Location: Little Rock, Arkansas
Posts: 35
|
Re: No reverse lights
PITA ?
Tool for ? please explain ? |
|
|
|
|
10-05-2006
|
#7 |
|
Join Date: Jan 2004
Location: Southern CA
Posts: 108
|
Re: No reverse lights
The switch can be replaced using tools available at Sears. Here is the information I posted in 2004.
The back-up light switch can be changed using common tools bought at sears. Buy a 22 mm 12 point deep socket, cut it off so it is just long enough to reach the bottom of the hex on the switch. Buy a 3 piece socket cap set from sears (these are adapters that plug into the socket that let you turn the socket with a wrench). Put the socket cap into the socket, put the socket on the switch after removing the electrical connector from the switch, and break the switch loose with a wrench. Remove the socket from the switch once the switch is loose enough that you can turn it by hand. There is not sufficient room to leave the socket on the switch and screw the switch all the way out. Before removing the switch you will need to take the slave cylinder loose from the bell housing and move it to the side to give you more room to work. There is also a small clamp on the line leading to the slave cylinder to remove to allow the slave cylinder to move easier. The piston in the slave cylinder is spring loaded and will extend when you remove the slave and you will have to re-compress the spring when you re-install the slave. |
|
|
|
|
10-07-2006
|
#8 |
 
Join Date: Jan 2006
Location: Decatur, AL
Posts: 1,119
|
Re: No reverse lights
did you ever get it fixed?
__________________
Corvette95 Registry and Forum (*************) 1989 C4 Conv Wht/Gry Auto Hardtop Top Flight SOLD 1995 C4 Coupe Purple/Blk 6 Speed 1989 C4 Conv Wht/Red Auto SOLD 1996 C4 Conv Black/Tan Auto SOLD 1994 C4 Coupe Wht/Blk SOLD 1995 C4 ZR-1 White/Gry #278 Dual Dunn Head SOLD 1986 C4 Coupe Black/Red 4+3 SOLD 1990 C4 ZR-1 Red/Red #0454 |
|
|
|
|
10-12-2006
|
#9 |
|
Join Date: Sep 2006
Location: Little Rock, Arkansas
Posts: 35
|
Re: No reverse lights
Not yet, looking for a lift.
|
|
|
|
|
10-12-2006
|
#10 |
|
Join Date: Jan 2004
Location: Southern CA
Posts: 108
|
Re: No reverse lights
I just use a floor jack and jackstands and/or rhino ramps.
|
|
|
|
 |
| Thread Tools | |
| Display Modes | |
|
|
Hybrid Mode
