Transmission fill / drain plug question

[Corbusa]

I went to drain my trans fluid today, and noticed someone had used channel locks or something on the fill plug, . it also looks like they might have tried the wrong tool on the inside of the plug. So my questions are what is the correct size of the fill and drain tools? and are the plugs available to buy? I'm sure there has got to be a few different transmissions that use the same plugs. ( ps i didnt remove the plugs , I am waiting to try and use the correct allen socket. thanks

[Dynomite]

Originally Posted by Corbusa

I went to drain my trans fluid today, and noticed someone had used channel locks or something on the fill plug, . it also looks like they might have tried the wrong tool on the inside of the plug. So my questions are what is the correct size of the fill and drain tools? and are the plugs available to buy? I'm sure there has got to be a few different transmissions that use the same plugs. ( ps i didnt remove the plugs , I am waiting to try and use the correct allen socket. thanks

17 mm Allen Wrench

Use a small hammer and tap allen wrench end into the center of the drain plug.
If that does not work....you will have to use channel locks or small pipe wrench on outside of plug.
Actually.......I would insert the 17 mm Allen by tapping and then place channel locks on outside using both wrenches.
The Trans Drain Plug is the same size and is usually scuffed from road rash.

You can use a larger box wrench over the end of the 17mm allen end as leverage along with the channel locks on outside of plug.

The transmission fill and drain Plug threads are M24 x 1.5 and zfdoc should have them

When you install the plugs use a bit of Permatex Form A Gasket Sealant (or similar) and do not tighten plugs too much.
See Note D LT5/ZR-1 Fluids

REMOVE THE FILL PLUG FIRST

[Corbusa]

Thanks Bro

[WVZR-1]

The plugs are 24 X 1.5 but I believe they're "tapered pipe" similar to our tapered pipe thread. You could do them locally but you give up the 17mm hex of the standaard ZF plug. If you're not concerned with the originality they should be quite readily available. An off the shelf 906 DIN I believe is a 12mm hex.

If your concern was just the "fill" plug you could actually do that with a "conventional hex" A conventional hex is a 909 DIN.

[Corbusa]

Guys will this work? http://www.ebay.com/itm/Auveco-18027...c4f28c&vxp=mtr

[WVZR-1]

Originally Posted by Corbusa

Guys will this work? http://www.ebay.com/itm/Auveco-18027...c4f28c&vxp=mtr

NO ! That plug is NOT a "tapered pipe thread". That is an oil/transmission style drain plaug that requires a gasket. Besides the BOX states 25mm x 1.5. The HEX is 24mm for the wrench.

Originally Posted by Corbusa

Also the drain plug is smaller , does anyone know what size allen? thank you ..

The drain & fill are the same! If yours are different then one or the other has been replaced with something other than OE. Cliff mentioned the 17mm hex and I mentioned it again.

[Corbusa]

Also the drain plug is smaller , does anyone know what size allen? thank you ..

[Corbusa]

Ok Thanks I guess my trans plugs have been changed . My drain is smaller . I did buy a 17 mm allen and it kind of fits the fill plug ( but someone messed it up ) the drain looks like maybe a 14-15 mm
Thanks WV
PS I did call ZRDOC last week but couldnt get a hold of anyone.

[WVZR-1]

Originally Posted by Corbusa

Ok Thanks I guess my trans plugs have been changed . My drain is smaller . I did buy a 17 mm allen and it kind of fits the fill plug ( but someone messed it up ) the drain looks like maybe a 14-15 mm
Thanks WV
PS I did call ZRDOC last week but couldnt get a hold of anyone.

You don't need him for the plugs. I'm sure they're off the shelf BMW, VW or MB.

I'll try to slip you a part number!

Here's a Magnetic with the correct 17mm hex BUT "NOT IN STOCK"!

https://www.pegasusautoracing.com/pr...asp?RecID=4060

[Corbusa]

M24X1.5, METRIC TAPER : EARLIER MANUAL TRANSMISSIONS







M24X1.5 TAPERED
A SPECIAL MADE DIMPLE® SUPER MAGNETIC DRAIN PLUG FOR THE BMW EARLIER MANUAL TRANSMISSIONS, now in true Yellow Chromate protective plating.

THIS PLUG IS THE LARGE M24X1.5 TAPERED METRIC THREAD.

IT FEATURES THE IDEAL FACTORY 17MM EXTERNAL HEX DRIVE. FITTED WITH A LARGE, DEEP SET, LOW PROFILE 1/2" DIAMETER MAGNET FOR OPTIMUM PERFORMANCE.

OUR INTENT IS TO KEEP YOUR TRANSMISSION CLEAN OF ALL HARMFUL METAL PARTICLES WHICH THEN ALLOWS SYNCHRONIZER'S AND BEARINGS TO ROTATE FREELY IN CLEAN OIL, FOR LONG LASTING DEPENDABILITY.

$34.95




YOU WILL BE GLAD TO KNOW THIS OIL PLUG FITS THE FOLLOWING BMW CHASSIS FITMENTS:

1 SERIES = E87

3 SERIES = E21, E30, E36, E46

5 SERIES = E12, E28, E34, E39

6 SERIES = E24

7 SERIES = E23, E32, E38

8 SERIES = E31

X5 = E53

Z3 = E36

Z4 = E85

Z8 =E52