GCs HID Headlight Install PICs - ZR-1 Net Registry Forums

GOLDCYLON · 09-28-2012

For those of you who expressed "Remote Interest"

So after buying this Plug and Play HI-Beam/LOW-Beam kit from Corvettehid.com website; what were my Impressions? Of this kit?

Quality: Top Notch
Ease of Install: Took longer than expected not truely plug and play
Wiring: Good quality once you figured it out
Instructions: OK color would have been nice in one area

Overall Impression Nice kit and happy with the end result. I went with the 50W Ballasts and the 4300K heat range kit.

So lets start. First the new Glass housings are Styrene backed inorder to prevent dirt and water from entering the projection housings. While this is a great idea it immediately causes problems with the install. This glass housing is longer than a standard glass headlight blub so metal spacers provided are needed as well when it comes time to secure the metal trim headlight retention frame.

So as you can clearly see.... LOTS of Styrene and the backside of the housings are now real fat so fitment is an issue into the standard headlight support bucket. The install instuctions say to bend back the housing support tabs. But there is no way that will work if you try to force it you will tear up all the styrene.

So GCs install solution cut the Headlight support bucket. NCRSers shield your eyes now

Cut the backsides, File them then reuse

Plenty of room for that back now and no chance of cutting or tearing up the styrene now once you file the cut area down that is !!!

Time to mount the New Headlight and housing and the support retention frame

See how long that bulb is now??? See the machined retention spacers now retaining the headlight with the gap?

GOLDCYLON · 09-28-2012

Plenty of room for the wiring to be plugged in and the Ballest to be installed. Suggest using both ties and the double sided tape provided in the kit

Plug in the Ballast its just an insert and turn and lock onto the backside of the HID bulb. Ziptie up all the connectors.

Now its splicing time tie into the Green wire on one end on the drivers side headlight control harness from the six wire headlight harness connector

Now tie into the green wire to that yellow wire that goes to the four wire connector to the headlight harness. This is all covered in the instuctions and the only wire tapping you will need to do.

efnfast · 09-28-2012

Hey GC, last pic. You had to take all that stuff on the ground off to do the headlights???

GOLDCYLON · 09-28-2012

Quote:

Originally Posted by efnfast

Hey GC, last pic. You had to take all that stuff on the ground off to do the headlights???

Quote:

Originally Posted by GOLDCYLON

Yes thats my point no way in Hades that simply bending back the tabs would work alone

Look how much further beyond the tabs you have to go. Bending them out of the way simply wont work

GOLDCYLON · 10-02-2012

How they look in action

And.... Something green thats operated by Remote the gill light kit. Very suttle

My thanks to the PNW crew including Kevin, Fred and his son, Sam and Jeff.

Scrrem · 10-02-2012

GC, Nice write up! Definently not a job for the faint of heart. Nice Gill lights too!!

How much more weight does that add to the headlight assembly? I am thinking about those plastic head light gears.
Rich

GOLDCYLON · 10-02-2012

Some words of caution on the plug and play wiring. The instructions stated "that many corvettes are miswired from the factory". While this may be true for the three prong Headlight plug be advised that the low beam wire to the three prong plug will either be a Green wire or a Tan wire or the High beam will be either Tan or Green.

This caused us a lot of grief as we were getting power to both wires no matter what the switch setting but no lights. The ground wire was miswired from Corvette HId into the Lowbeam wire position. Once when opened the supplied socket we were able to move the wires to the right pin location in the socket and the problem was sloved. Just something to be aware of.

Hope you enjoyed viewing the project. GC

GOLDCYLON · 10-02-2012

Quote:

Originally Posted by Scrrem

GC, Nice write up! Definently not a job for the faint of heart. Nice Gill lights too!!

How much more weight does that add to the headlight assembly? I am thinking about those plastic head light gears.
Rich

Thanks a few folks said why the hell green? I did want to confuse any drivers with Orange or Red. So green kind of stands out on the white paint.

GOLDCYLON · 10-02-2012

Quote:

Originally Posted by Scrrem

GC, Nice write up! Definently not a job for the faint of heart. Nice Gill lights too!!

How much more weight does that add to the headlight assembly? I am thinking about those plastic head light gears.
Rich

It will add weight Rich but I upgraded from the Hella housings which were also already glass so the mod really added nothing that I already didnt have. As we all know reguardless those Delran bushings will eventually need to be replaced again. I already did em once before a few years ago. The light output is outstanding. I avoided two deer on my trip back home because of this projection driving 30 miles South of Elko Nevada and a Skunk in Idaho. They truely are amazing and I consider them a safety item and well worth the bucks. GC

-=Jeff=- · 10-02-2012

what comes in the kit?

09-28-2012	#1
GOLDCYLON Join Date: May 2007 Location: Peoria, AZ Posts: 9,155	GCs HID Headlight Install PICs For those of you who expressed "Remote Interest" So after buying this Plug and Play HI-Beam/LOW-Beam kit from Corvettehid.com website; what were my Impressions? Of this kit? Quality: Top Notch Ease of Install: Took longer than expected not truely plug and play Wiring: Good quality once you figured it out Instructions: OK color would have been nice in one area Overall Impression Nice kit and happy with the end result. I went with the 50W Ballasts and the 4300K heat range kit. So lets start. First the new Glass housings are Styrene backed inorder to prevent dirt and water from entering the projection housings. While this is a great idea it immediately causes problems with the install. This glass housing is longer than a standard glass headlight blub so metal spacers provided are needed as well when it comes time to secure the metal trim headlight retention frame. So as you can clearly see.... LOTS of Styrene and the backside of the housings are now real fat so fitment is an issue into the standard headlight support bucket. The install instuctions say to bend back the housing support tabs. But there is no way that will work if you try to force it you will tear up all the styrene. So GCs install solution cut the Headlight support bucket. NCRSers shield your eyes now Cut the backsides, File them then reuse Plenty of room for that back now and no chance of cutting or tearing up the styrene now once you file the cut area down that is !!! Time to mount the New Headlight and housing and the support retention frame See how long that bulb is now??? See the machined retention spacers now retaining the headlight with the gap? __________________ GOLDCYLON - 91 ZR-1 #2014 GOLDCYLON - 90 ZR-1 #2794, 4L60e (Formerly Schrade's) GOLDCYLON - 11 CTS-V Arizona State Director 91 WHITE/BLACK #2014. 380 P&P&PCed,Ported Heads, Jeal Long tubes, Corsa Exhaust/FIKSE FM-5s /LED TLs, LED Headlights, Front Wilwood 6 piston narrowlite calipers and rear Wilwood caliper street shop mod,CNCed Coolant Pipes,TPI Cvr,Filter cover,Stainless Bolts, DRM/DOM PROM /ZFDOC mod build #102,DRLs,BMAD with stainless Debris Screen,Coplan Air Blaster, Pioneer APP Radio 4,Brey-Krause HB,Sub Bar,Fire extinguisher seat mount,DRM Coilovers,LEDs everywhere,Compass mirror (orange),V1 DIC hidden display, Homelink sun visor, Carbon Fiber top x3 and APSIS Carbon Fiber interior, APSIS CF Steering Wheel/NAPA Leather, Banski trailing arms, Guldstrand front suspension,urethane bushings from Prothane (total suspension) ZFDoc drive shaft safety loop, raptor shift light (orange),AO engineering louver front plate, Console seat cushion, 96CE seats with black custom Sheepskins, ss billet catch can,Viper remote entry/alarm,Cragar Rear Louvers,LED side louver lights, Dewitts Radiator with SPAL fans and a Woods 160 T-Stat 90 RED/BLACK #2794. 4L60e Automatic Stage V by RPM Transmission, TCI Dedicated TCM, OBX Stainless Headers, Corsa Exhaust, SAN Secondaries and Haibeck PROM, Exotic Muscle Coil overs, LED Interior Lights, LED Tail Lights, LED Headlights, 94 Sport seats with black custom Sheepskins , Cragar rear louvers, GS Front calipers, Banski Trailing arms, APSIS Carbon Fiber steering wheel, Front and Rear Baer Eradispeeds, DRLs, Guldstrand front suspension,urethane bushings from Prothane (total suspension), Dewitt's Raditor with Dual SPAL fans and a Haibeck 170 T-Stat 11 RED/GREY CTS-V Last edited by GOLDCYLON; 10-02-2012 at 02:49 PM.

09-28-2012	#2
GOLDCYLON Join Date: May 2007 Location: Peoria, AZ Posts: 9,155	Re: GCs HID Headlight and Gills LEDS Install PICs Plenty of room for the wiring to be plugged in and the Ballest to be installed. Suggest using both ties and the double sided tape provided in the kit Plug in the Ballast its just an insert and turn and lock onto the backside of the HID bulb. Ziptie up all the connectors. Now its splicing time tie into the Green wire on one end on the drivers side headlight control harness from the six wire headlight harness connector Now tie into the green wire to that yellow wire that goes to the four wire connector to the headlight harness. This is all covered in the instuctions and the only wire tapping you will need to do. __________________ GOLDCYLON - 91 ZR-1 #2014 GOLDCYLON - 90 ZR-1 #2794, 4L60e (Formerly Schrade's) GOLDCYLON - 11 CTS-V Arizona State Director 91 WHITE/BLACK #2014. 380 P&P&PCed,Ported Heads, Jeal Long tubes, Corsa Exhaust/FIKSE FM-5s /LED TLs, LED Headlights, Front Wilwood 6 piston narrowlite calipers and rear Wilwood caliper street shop mod,CNCed Coolant Pipes,TPI Cvr,Filter cover,Stainless Bolts, DRM/DOM PROM /ZFDOC mod build #102,DRLs,BMAD with stainless Debris Screen,Coplan Air Blaster, Pioneer APP Radio 4,Brey-Krause HB,Sub Bar,Fire extinguisher seat mount,DRM Coilovers,LEDs everywhere,Compass mirror (orange),V1 DIC hidden display, Homelink sun visor, Carbon Fiber top x3 and APSIS Carbon Fiber interior, APSIS CF Steering Wheel/NAPA Leather, Banski trailing arms, Guldstrand front suspension,urethane bushings from Prothane (total suspension) ZFDoc drive shaft safety loop, raptor shift light (orange),AO engineering louver front plate, Console seat cushion, 96CE seats with black custom Sheepskins, ss billet catch can,Viper remote entry/alarm,Cragar Rear Louvers,LED side louver lights, Dewitts Radiator with SPAL fans and a Woods 160 T-Stat 90 RED/BLACK #2794. 4L60e Automatic Stage V by RPM Transmission, TCI Dedicated TCM, OBX Stainless Headers, Corsa Exhaust, SAN Secondaries and Haibeck PROM, Exotic Muscle Coil overs, LED Interior Lights, LED Tail Lights, LED Headlights, 94 Sport seats with black custom Sheepskins , Cragar rear louvers, GS Front calipers, Banski Trailing arms, APSIS Carbon Fiber steering wheel, Front and Rear Baer Eradispeeds, DRLs, Guldstrand front suspension,urethane bushings from Prothane (total suspension), Dewitt's Raditor with Dual SPAL fans and a Haibeck 170 T-Stat 11 RED/GREY CTS-V Last edited by GOLDCYLON; 10-02-2012 at 09:11 PM.

09-28-2012	#3
efnfast Join Date: Nov 2011 Location: Dunbarton NH Posts: 7,486	Re: GCs HID Headlight Install PICs Hey GC, last pic. You had to take all that stuff on the ground off to do the headlights???

10-02-2012	#5
GOLDCYLON Join Date: May 2007 Location: Peoria, AZ Posts: 9,155	Re: GCs HID Headlight Install PICs How they look in action And.... Something green thats operated by Remote the gill light kit. Very suttle My thanks to the PNW crew including Kevin, Fred and his son, Sam and Jeff. __________________ GOLDCYLON - 91 ZR-1 #2014 GOLDCYLON - 90 ZR-1 #2794, 4L60e (Formerly Schrade's) GOLDCYLON - 11 CTS-V Arizona State Director 91 WHITE/BLACK #2014. 380 P&P&PCed,Ported Heads, Jeal Long tubes, Corsa Exhaust/FIKSE FM-5s /LED TLs, LED Headlights, Front Wilwood 6 piston narrowlite calipers and rear Wilwood caliper street shop mod,CNCed Coolant Pipes,TPI Cvr,Filter cover,Stainless Bolts, DRM/DOM PROM /ZFDOC mod build #102,DRLs,BMAD with stainless Debris Screen,Coplan Air Blaster, Pioneer APP Radio 4,Brey-Krause HB,Sub Bar,Fire extinguisher seat mount,DRM Coilovers,LEDs everywhere,Compass mirror (orange),V1 DIC hidden display, Homelink sun visor, Carbon Fiber top x3 and APSIS Carbon Fiber interior, APSIS CF Steering Wheel/NAPA Leather, Banski trailing arms, Guldstrand front suspension,urethane bushings from Prothane (total suspension) ZFDoc drive shaft safety loop, raptor shift light (orange),AO engineering louver front plate, Console seat cushion, 96CE seats with black custom Sheepskins, ss billet catch can,Viper remote entry/alarm,Cragar Rear Louvers,LED side louver lights, Dewitts Radiator with SPAL fans and a Woods 160 T-Stat 90 RED/BLACK #2794. 4L60e Automatic Stage V by RPM Transmission, TCI Dedicated TCM, OBX Stainless Headers, Corsa Exhaust, SAN Secondaries and Haibeck PROM, Exotic Muscle Coil overs, LED Interior Lights, LED Tail Lights, LED Headlights, 94 Sport seats with black custom Sheepskins , Cragar rear louvers, GS Front calipers, Banski Trailing arms, APSIS Carbon Fiber steering wheel, Front and Rear Baer Eradispeeds, DRLs, Guldstrand front suspension,urethane bushings from Prothane (total suspension), Dewitt's Raditor with Dual SPAL fans and a Haibeck 170 T-Stat 11 RED/GREY CTS-V Last edited by GOLDCYLON; 10-02-2012 at 11:29 AM.

10-02-2012	#6
Scrrem Join Date: Feb 2009 Location: Alexandria, Virginia Posts: 1,467	Re: GCs HID Headlight Install PICs GC, Nice write up! Definently not a job for the faint of heart. Nice Gill lights too!! How much more weight does that add to the headlight assembly? I am thinking about those plastic head light gears. Rich __________________ 1990 Bright Red Coupe #608 380 Stroker, Ported Heads/Intake/Housings/TB Haibeck Secondary Delete Chip / Pete's Cams George Braml Intake / FIC Injectors Coated SW Headers / Corsa Bill Boudreau B/B ZF6 / Viper 4.10 gears Ron Davis Radiator Pioneer AVIC-Z140BH NAV Fikse FM5's 285 / 335 / C6 Brakes WAZOO Member Last edited by Scrrem; 10-02-2012 at 11:29 AM.

10-02-2012	#10
-=Jeff=- Join Date: Jul 2007 Location: Bartlett, IL Posts: 7,169	Re: GCs HID Headlight Install PICs what comes in the kit? __________________ 1990 Corvette ZR-1 #1051 Watson Headers (2" Primary) - Flowmaster Cats - Borla Catback Late Model IH - Plenum Coilovers - 4.10s Custom Interior NCM Lifetime Member #978

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode