Re: TB removal and then some!!!
 

Where the oil pressure sensor screws into...if you use your Z on a consistent basis....I would imagine that there wouldn't be any need for an Accu-Sump.....JMO....

Sent from my SM-G981U using ZR-1 Net Registry mobile app

Re: TB removal and then some!!!
 

Need some info on removing the bolt from the front sway bar bracket that attaches to the LCA....this bolt won't budge either with electric impact or tapping the bolt out with a small sledge....so before I do any damage... does this bolt slide through the bushing sleeve...(which I'm thinking)...or is it threaded through....
thanks for any info....[emoji16][emoji16]Attachment 17356

Sent from my SM-G981U using ZR-1 Net Registry mobile app

Re: TB removal and then some!!!
 

If that is the upper stabilizer bar insulator then yes it slides through the sleeve.

Re: TB removal and then some!!!
 

That is the lower part of the bracket Gary....attached to the LCA and found out that it also slides out.... thanks...[emoji16][emoji16]

Sent from my SM-G981U using ZR-1 Net Registry mobile app

Re: TB removal and then some!!!
 

Get a cheap socket put the head of the bolt in the socket and hammer it once it starts to move you should be able to get it out the rest of the way

Sent from my SM-T865 using ZR-1 Net Registry mobile app

Re: TB removal and then some!!!
 

Back on the ZR-1 this afternoon...
finally got the sway bar bracket removed....did a preliminary cleaning of the LCA and the bracket after a short soak....bracket is in for more soaking...getting there....Attachment 17381Attachment 17383Attachment 17384Attachment 17385Attachment 17386Attachment 17387

Sent from my SM-G981U using ZR-1 Net Registry mobile app

Re: TB removal and then some!!!
 

Can't tell you the number of times I have stripped...sanded and resprayed and then clear coated the plenum over the last almost 4 years..... I know I could have got it powder coated...but also like the feeling of do as much as I can myself....so after repainting the plenum months ago.... today I finally clear coated this piece once again....may not be perfect... but looks good enough to install...
also the LS sway bar bracket after soaking for a few days in Evapo-Rust....paint literally just wiped off....liking the bare metal finish. .especially in the comparison pics.....may leave as it and just clear coat....[emoji16][emoji16]Attachment 17391Attachment 17392Attachment 17394Attachment 17395Attachment 17396

Sent from my SM-G981U using ZR-1 Net Registry mobile app

Re: TB removal and then some!!!
 

This thread just hit 80 pages--Is this a Forum record? Been a fun thread to follow. --Bob

Re: TB removal and then some!!!
 

Thanks Bob....it has been fun....[emoji16][emoji16]

Sent from my SM-G981U using ZR-1 Net Registry mobile app

Re: TB removal and then some!!!
 

Been extremely busy recently...not totally ZR-1 related...as our "new" Yellow 74 Convertible came home last week...and our Brown 74 Convertible went down to GA for some engine work....which now leaves time to devote fully to the 94....always something going on....[emoji16][emoji16]
Pic #1....still need more cleaning and painting to finish....was thinking about removing the cam covers for painting....but might just tape everything off and paint them on the engine....
Pic #2.....our "new" 74 Convertible is home....while not cosmetically perfect....the L-82 is rebuilt and all new suspension in place....
Pic #3...our 74 LS4 454 loaded and now in GA for some engine work.... no return time frame...so now full concentration for the ZR-1....[emoji16][emoji16]Attachment 17569Attachment 17570Attachment 17571

Sent from my SM-G981U using ZR-1 Net Registry mobile app