|
Re: TB removal and then some!!!
5 Attachment(s)
Making progress with the positive battery cable replacement....
Everything is apart...was debating on removing the starter and doing a cleanup...but may just leave as it is and clean what I can.... Pic #1....yes we know how crowded it is under there....lol Pic #2....that tape gun tape doesn't stick... [emoji848]....now what plug goes where....[emoji16][emoji16] Pic #3....connections everywhere... great opportunity to get everything cleaned... Pic #4....glad I removed the coils from the cover plate...needs a cleaning.... Pic #5...and there it is....the positive battery cable connection....was thinking about starter removal...but now....thinking not....[emoji16]Attachment 13414Attachment 13415Attachment 13416Attachment 13417Attachment 13418 Sent from my SM-G981U using ZR-1 Net Registry mobile app |
Re: TB removal and then some!!!
Since you have gone to that trouble, I would at least pull the starter and check/clean the solenoid contacts.
H :cheers: |
Re: TB removal and then some!!!
Quote:
Sent from my SM-G981U using ZR-1 Net Registry mobile app |
Re: TB removal and then some!!!
Dude.... pull the starter... clean it up and clean that valley up too. Youve gone too far not to. :thumbsup:
|
Re: TB removal and then some!!!
6 Attachment(s)
Well I did end up removing the starter and did a cleanup in the valley...the drain hole was clear....as that was taken care of with the 1st plenum pull years ago...some pics.... btw...the FSM....mentions to torque the starter bolts to 38 lb ft.... is any type of sealer or anti seize recommended???
Pic #1...some cleaning needed for sure... Pic #2...there is some crud there....lol... Pic #3...used a 14" plastic tie for the drain hole....clear all the way through... Pic #4...wiped out and looking like it should.... Pic #5...as clean as can be...an improvement from before....:) Pic #6...starter back in...bolts need to be torqued down....thinking about a dab of anti-seize for future removal.... Another job added to the finished column....:):) Attachment 13429Attachment 13430Attachment 13432Attachment 13433Attachment 13434Attachment 13435 Sent from my SM-G981U using ZR-1 Net Registry mobile app |
Re: TB removal and then some!!!
I know of no sealant needed for the starter mounting... Looking good now!!
|
Re: TB removal and then some!!!
Quote:
|
Re: TB removal and then some!!!
2 Attachment(s)
Replacement positive battery cable installed....had to use original ground wire....no biggie...just had to retape to replacement....[emoji16]Attachment 13450Attachment 13451
Sent from my SM-G981U using ZR-1 Net Registry mobile app |
Re: TB removal and then some!!!
5 Attachment(s)
More progress today....cleaning up more under the plenum....
Pic #1...from this.... Pic #2...to this.... Pic #3...and this.... Pic #4...to this... Pic #5...going to remove the AC compressor and the alternator for a full cleaning....and most likely the belt tensioner while I'm at it....lol before you know it I'll have the entire car disassembled......[emoji16][emoji848][emoji16]Attachment 13460Attachment 13461Attachment 13462Attachment 13463Attachment 13464 Sent from my SM-G981U using ZR-1 Net Registry mobile app |
Re: TB removal and then some!!!
3 Attachment(s)
Coil tray cleaned and ready for install....back in the engine with colis and wires attached....Attachment 13473Attachment 13474Attachment 13475
Sent from my SM-G981U using ZR-1 Net Registry mobile app |
| All times are GMT -4. The time now is 10:52 PM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2025, vBulletin Solutions Inc.
Copyright ZR-1 Net Registry 2025