|
05-11-2015
|
#11 |
 Join Date: May 2013
Location: Beaver, PA
Posts: 516
|
Re: Jerry's LT5 Paint
Steve it will look real good I'm sure.
Gotta be something in that metal that is reacting to the paint. A good primer sealer would probably cure that. Are you doing the injector housings too? |
|
|
|
05-11-2015
|
#12 |
|
Join Date: Apr 2015
Location: Northwest AR
Posts: 95
|
Re: Jerry's LT5 Paint
It might be something in the metal. The previous owner cleaned it with something that left spots all over it that will not come off, hence wanting to repaint it. I was also surprised after pulling the plennum that there was mouse crap under it. Guess a mouse set up shop in there. Nothing chewed on though.
|
|
|
|
|
05-11-2015
|
#13 | |
  
Join Date: Aug 2009
Location: South Dakota/California
Posts: 3,788
|
Re: Jerry's LT5 Paint
Quote:
Since you are Powder Coating....I think you are only doing the Plenum....too bad you are not removing the Cam Covers and get all three done at the same time  This is Spray Paint.....  This is Powder Coat.... 
__________________
Left Clickable links -Solutions- LT5 Modifications/Rebuild Tricks Low Mileage ZR-1 Restoration 1990 Corvette (L98) Modifications LT5 Eliminated Systems LT5 Added Systems LT5/ZR-1 Fluids 1995 LT5 SPECIFIC TOP END REBUILD TRICKS Last edited by Dynomite; 05-11-2015 at 08:03 PM. |
|
|
|
|
|
05-11-2015
|
#14 |
|
Join Date: Apr 2015
Location: Northwest AR
Posts: 95
|
Re: Jerry's LT5 Paint
I am just going to get a color close to stock. The cam covers are more than I want to tackle at this point. Maybe this winter will do the cam covers as well as the ported housings and retune. Right now just getting it to a solid driver status.
|
|
|
|
|
05-11-2015
|
#15 |
|
Join Date: Feb 2011
Location: San Marcos CA
Posts: 1,802
|
Re: Jerry's LT5 Paint
I just polished mine with a fine polish and a foam pad...it had the etching from harsh cleaners that screw up these LT5's.
As far as the paint, I'd say dewax with a naphtha solvent them follow with rubbing alcohol. |
|
|
|
|
05-11-2015
|
#16 |
 Join Date: Apr 2004
Location: ATL. GA.
Posts: 2,162
|
Re: Jerry's LT5 Paint
Marc Haibeck Paint ... fine silver
__________________
Steve 1990 Steel Blue/Black #2355 1990 Red/Red #1473 1991 Quasar /Black #118 Sold 1991 Turquoise/Black #766 Parted Out 1993 Yellow/White #179 Sold 1990 Black/Gray #1361 Headers/4:10s Sold |
|
|
|
|
05-12-2015
|
#17 |
|
Join Date: Jan 2007
Location: Florida
Posts: 241
|
Re: Jerry's LT5 Paint
I repainted mine with LPE LT5 paint with no issues. I did my cam covers on the car by pulling everything and securing everything away and masked the the rest of the car. I also masked the lines I did not want to disconnect and the bolt heads. This is with the plenum and injector housings off the motor. Trust me if you do the plenum and injector housings and not the cam covers you will not like the results.
Good luck! Jim |
|
|
|
 |
|
|
Linear Mode
