Forum: C4 ZR-1 Technical Postings
02-13-2016
|
|
Replies: 41
Views: 6,834
Re: Bogging after Coasting
Thanks. Will do.
They are from Banski Motorsports: anodized aluminum rear trailing arms, toe rods, and camber rods, all with heim jointed ends.
|
|
Forum: C4 ZR-1 Technical Postings
02-13-2016
|
|
Replies: 41
Views: 6,834
Re: Bogging after Coasting
I finally had a chance to look at the car today. As I was driving the car around before I had the scanner hooked up the bogging issue was evident. When I got home I took a scan at hot idle to...
|
|
Forum: C4 ZR-1 Technical Postings
01-17-2016
|
|
Replies: 41
Views: 6,834
|
|
Forum: C4 ZR-1 Technical Postings
01-16-2016
|
|
Replies: 41
Views: 6,834
Re: Bogging after Coasting
Good points guys. I did check the tps with my tech1. Seems good and it's new but I'll check again to ensure I haven't missed anything. I also put in a new MAT sensor when I first got the car back...
|
|
Forum: C4 ZR-1 Technical Postings
01-12-2016
|
|
Replies: 41
Views: 6,834
|
|
Forum: C4 ZR-1 Technical Postings
01-11-2016
|
|
Replies: 41
Views: 6,834
Re: Bogging after Coasting
Looks like he's about 4 hrs 15 mins away. Kind of far. I could do a tunerpro log.
I never had stock Z06 rotors on the car, so I can't compare to those. They're pretty light ( lighter than stock...
|
|
Forum: C4 ZR-1 Technical Postings
01-11-2016
|
|
Replies: 41
Views: 6,834
|
|
Forum: C4 ZR-1 Technical Postings
01-11-2016
|
|
Replies: 41
Views: 6,834
Re: Bogging after Coasting
Ok, yep, it is the same. Mine seems to do it every time I get back on the gas though. What injectors do you have?
|
|
Forum: C4 ZR-1 Technical Postings
01-11-2016
|
|
Replies: 41
Views: 6,834
Re: Bogging after Coasting
Paul,
Your issue does sound similar, but mine never stalls. It just hesitates bad as I tip in the throttle after decel. If I mash the throttle, it'll jolt back to normal, almost like a really bad...
|
|
Forum: C4 ZR-1 Technical Postings
01-10-2016
|
|
Replies: 41
Views: 6,834
|
|
Forum: C4 ZR-1 Technical Postings
01-10-2016
|
|
Replies: 41
Views: 6,834
|
|
Forum: C4 ZR-1 Technical Postings
01-10-2016
|
|
Replies: 41
Views: 6,834
Bogging after Coasting
I'm still having the problem with bogging on throttle after coasting. This started after I had the intake ported and removed the secondaries. It seems to not happen until the car gets hot (fully...
|
|
Forum: C4 ZR-1 Technical Postings
11-29-2015
|
|
Replies: 7
Views: 1,520
Re: Stainless Works Header Warped
Thank you all for the replies. I will continue on with my install. Then on to the corsa install.
On a side note- I found no less than 12 leaks in my old exhaust on the front cat welds. Also...
|
|
Forum: C4 ZR-1 Technical Postings
11-28-2015
|
|
Replies: 7
Views: 1,520
Stainless Works Header Warped
I was going to install my new stainless works headers, and as I checked the driver's side header for straightness, I noticed that it was warped by .045" in between #1 and #3. Each port is straight,...
|
|
Forum: C4 ZR-1 Technical Postings
09-20-2015
|
|
Replies: 56
Views: 13,013
Re: Engine Ticking
OK, so I replaced the O2 sensors with OE type AC Delcos and also tightened the header bolts. Several were slightly loose. This seemed to have helped the problems a lot, but was not a 100% fix. It...
|
|
Forum: C4 ZR-1 Technical Postings
08-27-2015
|
|
Replies: 56
Views: 13,013
Re: Engine Ticking
They are new densos. I had the same issue with the old ones that were in there too, but I'm not sure which brand those were.
|
|
Forum: C4 ZR-1 Technical Postings
08-27-2015
|
|
Replies: 56
Views: 13,013
Re: Engine Ticking
I have Marcs normal BPPAG4 cal with custom settings:
Add fuel for headers
Fuel for cats
Enable anti-backfire mode
Add Fuel for top end porting
Secondaries removed
750 rpm idle
7200 rpm rev...
|
|
Forum: C4 ZR-1 Technical Postings
08-26-2015
|
|
Replies: 56
Views: 13,013
Re: Engine Ticking
The bog after coasting is back (well, actually, when I thought it was gone, I wasn't off of the throttle enough for it to appear, still have a rough idle as well). It bogs if I let off the throttle...
|
|
Forum: C4 ZR-1 Technical Postings
08-06-2015
|
|
Replies: 56
Views: 13,013
Re: Engine Ticking
I have not, but I just got a can of the stuff that you can spray into the intake. It has the long straw with the bend in it.
|
|
Forum: C4 ZR-1 Technical Postings
08-04-2015
|
|
Replies: 56
Views: 13,013
Re: Engine Ticking
OK, so I replaced the throttle stop with a bolt and ran through the procedure you have posted. IAC counts are now at 12, and TPS at .55 volts. The car is more responsive and seems to not have a...
|
|
Forum: C4 ZR-1 Technical Postings
07-28-2015
|
|
Replies: 56
Views: 13,013
Re: Engine Ticking
The IAC counts at idle are 25, cold open loop. The TPS voltage was at .50, which is weird because I set it at .54. With the engine off and pressing and releasing the throttle it settles at .52 or...
|
|
Forum: C4 ZR-1 Technical Postings
07-28-2015
|
|
Replies: 56
Views: 13,013
Re: Engine Ticking
Just tried that out- no change. I had the old connector zip tied, but this new Jerry's one is really tight. Checked the pressure regulator vacuum line, that was good. I also took a look at the...
|
|
Forum: C4 ZR-1 Technical Postings
07-28-2015
|
|
Replies: 56
Views: 13,013
Re: Engine Ticking
No worries - I don't believe it has been discussed, although the map and the hose (plastic) are relatively new. The MAP seems to be reacting correctly on the tech 1. The sensor under the ecm is...
|
|
Forum: C4 ZR-1 Technical Postings
07-28-2015
|
|
Replies: 56
Views: 13,013
Re: Engine Ticking
All of the pcv parts are new and attached snugly, but there could be a leak somewhere. I'll see if I can find a leak with a homebuilt smoke machine or something.
|
|
Forum: C4 ZR-1 Technical Postings
07-27-2015
|
|
Replies: 56
Views: 13,013
Re: Engine Ticking
Just a little update:
I ran through the fuel pressure test procedure and was getting almost instant leakdown, so I replaced both pumps. Now I get 52 psi when the pumps are running, which drops...
|
