Vegas in September

[4DSZR1]

I'm just curious......Who's planning on going to the PNW Gathering in Las Vegas?

[Jeffvette]

I'll be there. If I'm bringing a car I may haul it down. But I may be flying.

[tf95ZR1]

I'll be there.
Jeff promised to bring some of the honeys in his avatar.
:dancing
I'll be there........

[GOLDCYLON]

Jeff promised to bring some of the honeys in his avatar.
:dancing
I'll be there........


Hmmm :eusa_shhh I heard the real story is Jeff has all those honeys and has no time to show up. :mrgreen:

[cuisinartvette]

I should be there this year.

[PhillipsLT5]

I will be there again
Goldcylon, you better be going

[GOLDCYLON]

Will need to check in with Household 6!!!! BTW

PS P&P and PC job is done. Awaiting two parts before the big reveal. Taking her to the Dyno tomorrow.

[tf95ZR1]

P&P and PC job is done. Awaiting two parts before the big reveal. Taking her to the Dyno tomorrow.
Pics Pics!

[cuisinartvette]

Will need to check in with Household 6!!!! BTW

PS P&P and PC job is done. Awaiting two parts before the big reveal. Taking her to the Dyno tomorrow.
Awesome! I was hoping to get some porting and headers done before this years event but it will have to wait til winter.
Oh well, someone has to be the slow guy :mrgreen:

[GOLDCYLON]

Awesome! I was hoping to get some porting and headers done before this years event but it will have to wait til winter.
Oh well, someone has to be the slow guy :mrgreen:

It took 4 months of planning and parts chasing. 3 weeks of assembly/disassembly and the support and counsel of Jeffvette, the ZF.Doc and Carter200 with some special engraving. Zethco hooked me up with the stainless bolts and part numbers. I am awaiting the camcover emblems for the reveal.

Heres a talley of what was done!!!

Porting and polishing of entire top end to include plenum, air horn and injector housings. Entire top end from Throttle shield cover to MAP sensor bracket was powercoated in Silver Metallic Paint with red and black lettering. All work done by Jeffvette.

Diassembly and assembly was completed by Bill B the ZF.Doc and his trusty helper. I chose to replace the following during the tear down.

Removed Original Injectors and replaced with RC SL4-205s (all the originals were rusted BTW)
New Plugs, Iridium of course
New Wires, Delco of course
4 New Delco Coil Packs
1 New Starter
2 New PCV Valves and PCV tubing
1 New MAP sensor but dammit I bought the wrong part (lol)

Carter provided Machined LT-5 Coolant Pipes, LT-5 TPI Cover and a ZR-1 Billet Oil Filter cover

Zethco hooked me up with Macallister for all the stainless hardware

Pics to follow, If I can get a kitchen pass after pulling off all these mods with Household 6 I will be in LV for at least a few days. :)

All these folks made this happen and the Permagrin continues to get wider. It all about the car and the people folks!! Goldcylon

[cuisinartvette]

Sounds nice! I left mine intact, a simple porting job I cant do withou probably going through and compulsively replacing everyhing under it wether it needs it or not. :icon_scra One thing leads to another all to often over here....Heck just pulled the radiator last year to clean it....It was down for an entire yeare with "what abouts".

Sure good at taking them apart though. :sign10:

[tf95ZR1]

Diassembly and assembly was completed by Bill B the ZF.Doc and his trusty helper. Goldcylon

I didn't know Bill also did engine work.


I am awaiting the camcover emblems for the reveal

Boy, so am I awaiting (2) emblems. Jeff??

[cuisinartvette]

Bill and his wife doing LT5s now?

[GOLDCYLON]

Sounds nice! I left mine intact, a simple porting job I cant do withou probably going through and compulsively replacing everyhing under it wether it needs it or not. :icon_scra One thing leads to another all to often over here....Heck just pulled the radiator last year to clean it....It was down for an entire yeare with "what abouts".

Sure good at taking them apart though. :sign10:

Its a while you are there approach... Hate to get her done and then dohh Wish I would have done that!! Adds to the project costwise but at that point it becomes MOD dust price wise. And from my view I have no idea if its been seen too in 17 years, my guess was probably not:thumbsup:

[GOLDCYLON]

[quote=tf95ZR1]I didn't know Bill also did engine work.

Yep him and his partner do, Including the heads matched machine porting. Its great to have him less than 20 Miles away!! ;)

Frankly I was happy he could take this job on!!!

[GOLDCYLON]

Bill and his wife doing LT5s now?

Negative just a collegue :o

And from what I saw he does LT-1s and LT-4s as well. He happiest when working Ive found :)

[carter200]

It took 4 months of planning and parts chasing and the support and counsel of Carter200 with some special engraving.

Carter provided Machined LT-5 Coolant Pipes, LT-5 TPI Cover and a ZR-1 Billet Oil Filter cover

It all about the car and the people folks!! Goldcylon

Thanks for the kind words GOLDCYLON. It was a pleasure helping you and hope all else goes good:cheers:

[jonszr1]

I might show for the drag racing. just depends...........

[GrayZ]

I might show for the drag racing. just depends...........

I think you better wear jeans. although many of our sexy senior citizens
might appreciate your thought, I for one, vote no.

I don't think there is anyway i'm gonna make it to Vegas.:cry: