Dump valve Exhaust project

[Mr.Yuck]

Step (1) cut apart a perfectly good Billy Boat fusion exhaust system and pray you made the right decision....177731777417775177761777717778

The older I get the faster I was.

[Mr.Yuck]

Step. (2) Everything is cut and mocked up, ready to weld.17780177811778217783

The older I get the faster I was.

[WARP TEN]

Looks great--I did something similar on my '95. I wanted a stock exhaust for the appearance and lack of drone, but with cutouts to have an open exhaust when I wanted it. I usd QTP electric cutouts and hid a rocker switch under the carpet on the passenger side of the console. Located the cutouts right in front of the mufflers to preserve the spare tire carrier. Either your way or mine works well. --Bob

[aafc]

http://www.zr1.net/forum/picture.php?albumid=343&pictureid=3053






In 216 I had power effects exhaust system and a friend waned it for his car.
I told him give me some time to fab up a new system. Long story I got a
used LT1 exhaust system, added dual dumps with QTP electric ( I removed
the spare tire assembly as I run a transmission cooler in that location).
Have been running this setup since mid 2016, I get good comments from
everyone who sees and hears it.
John
1990 white/black # 2546
one of a few 4l8OE QE ZR-1"s

[tf95ZR1]

Hey aafc
What is the red cable in the pic?

Never mind. Suspect for trans cooler.

[Mr.Yuck]

I'm going with the full wireless module set up. Super small, smaller than a pack of cigarettes really concealable. Just needs 12V and a ground and comes with two key fobs.17797

The older I get the faster I was.

[XfireZ51]

When I tried to adapt the Mild to Wild setup for my Z06 NPP valves, I ran into an interesting anomaly. If I fed power to the vacuum solenoid from 12v battery, the system worked. However if I fed power from the car?s electrical system, it would not work. The only thing I could come up w was that the vehicle electrical system somehow interfered w the wireless signal. Ultimately, I just ran wires to the back where the solenoid is located and a rocker switch in the console cup holder.

[Mr.Yuck]

This valve set up is completely electric. Should be finishing up the install this weekend.. 17799

The older I get the faster I was.

[gtcollins@maxnet.co.nz]

Hi here is what I have done I used the QTP remote as well I made a defuser for landspeed racing quite when you want it and sounds awesome when you're on it I also open the valves just abit when I drive the car it doesn't seem to drone and it sounds good from inside the car a friend rang me one night when I was out cruising around in my car and said it sounds great as I had driven passed him with the valves partially open I have my own headers and 3" exhaust system in front of this 1781717818178191782017821

Sent from my SM-G998B using ZR-1 Net Registry mobile app (http://r.tapatalk.com/byo?rid=90383)

[gtcollins@maxnet.co.nz]

Hi and a drive by at wide open just in case you haven't seen or heard it before


https://youtu.be/eVtmCmN4038


Sent from my SM-G998B using ZR-1 Net Registry mobile app (http://r.tapatalk.com/byo?rid=90383)

[aafc]

Red cable + feed from relocated battery behind passenger seat.
Transmission cooler is connected by stainless hose with AN fittings
John

[gtcollins@maxnet.co.nz]

Hi just had a look on QTP web page for the red remote controls it looks like red system opens the QTP valves all the way with one push of the button as opposed to the black system which allows you to open the valves partially

Glen Collins

Sent from my SM-G998B using ZR-1 Net Registry mobile app (http://r.tapatalk.com/byo?rid=90383)

[HAWAIIZR-1]

Hi here is what I have done I used the QTP remote as well I made a defuser for landspeed racing quite when you want it and sounds awesome when you're on it I also open the valves just abit when I drive the car it doesn't seem to drone and it sounds good from inside the car a friend rang me one night when I was out cruising around in my car and said it sounds great as I had driven passed him with the valves partially open I have my own headers and 3" exhaust system in front of this 1781717818178191782017821

Sent from my SM-G998B using ZR-1 Net Registry mobile app (http://r.tapatalk.com/byo?rid=90383)



Glen,
That is one awesome setup you have there mate! Wow! I love it! It?s friggin cool and badass!!


Sent from my iPhone using ZR-1 Net Registry (http://r.tapatalk.com/byo?rid=90383)

[gtcollins@maxnet.co.nz]

Hi Craig thank's for that

Glen

Sent from my SM-G998B using ZR-1 Net Registry mobile app (http://r.tapatalk.com/byo?rid=90383)

[Mr.Yuck]

Step (3) I just finished up the welding. I have a little bit more cleaning up to do. But turned out pretty good I think.. Placing the cut outs here gives me zero flow restriction with the dump valves open pretty much a straight shot..1783617837

The older I get the faster I was.

[HAWAIIZR-1]

Hi Craig thank's for that

Glen

Sent from my SM-G998B using ZR-1 Net Registry mobile app (http://r.tapatalk.com/byo?rid=90383)


You are welcome Glen. It?s always to you hear and see what you are doing over there. Great stuff!


Sent from my iPhone using ZR-1 Net Registry (http://r.tapatalk.com/byo?rid=90383)

[Mr.Yuck]

All completed. It Sounds amazing. The remote wireless set up is the cat's pajamas so far..178841788517886

The older I get the faster I was.

[mpiecyk]

Hi Mr. Yuck, Very nice and well engineered installation I like the pic showing the exhaust tires and suspension what a monster hope to see you at Marc gathering next Sunday June 5,2022.

[JT ZR-Won]

Step (1) cut apart a perfectly good Billy Boat fusion exhaust system and pray you made the right decision....17777

Wow, very cool project! What kind of X-pipe is that?

Jay

[Mr.Yuck]

The exhaust is a Billy Boat Fusion system. You could order it back in the day with a resonator or X pipe. The cut out kit I bought from Quick Time Performance it's a 3" Do-it-yourself cut out kit Made the USA. I'm really happy with the quality. I had a lot of fabrication to make it work because it's a universal kit but I think it turned out good. 17895

The older I get the faster I was.