WTB crank sensor connextor

[-=Jeff=-]

I am looking for the 3 wire crank sensor connector found on the Ignition Module. I can find the harness side but I want the module side connector.. thanks

9457


Sent from my iPhone using ZR-1 Net Registry (http://r.tapatalk.com/byo?rid=90383)

[spork2367]

https://www.jerrysgaskets.com/connector-dis-ignition-module-l-rear-1990-95-12b5/

[-=Jeff=-]

Thanks but I need the IM side of the connector

[spork2367]

Thanks but I need the IM side of the connector

I guess I'm unclear as to what you're looking for. The connector in the link is the connector that plugs into the left rear of the module. The connector on the module is molded into the entire case.

Are you just looking for a female connector that would match the cases connector?

If so, it's this one:

https://theelectricaldepot.com/weather-pack-delphi-connectors/metri-pack-150-series-sealed/12129615-dellphi-3-way-metri-pack-150-male-sealed-br-5-count-bag?zenid=9a146d3cd580fb7c950ae6902b383fa4

[secondchance]

https://www.whiteproducts.com/fusible_link_wire.shtml

Go to the website and download online catalog. Looks like Metri-pack 1508.

[-=Jeff=-]

I guess I'm unclear as to what you're looking for. The connector in the link is the connector that plugs into the left rear of the module. The connector on the module is molded into the entire case.

Are you just looking for a female connector that would match the cases connector?

If so, it's this one:

https://theelectricaldepot.com/weather-pack-delphi-connectors/metri-pack-150-series-sealed/12129615-dellphi-3-way-metri-pack-150-male-sealed-br-5-count-bag?zenid=9a146d3cd580fb7c950ae6902b383fa4

Yes I want the female connector to match the connector on the harness..

I have the one you posted (series 150 and I don't believe it fits.. I will check again, but if I recall it is too wide

Yun,

1508 is the harness side connector, yes, it is a series 150.2 pull to seat. I have not been able to find the female mate to it, that is what I need

essentially I want to plug it into the harness

[secondchance]

http://www.dstgateway.com/ACDelcoConnectorsV2/#/catalog

Also check PT 2353.

[-=Jeff=-]

http://www.dstgateway.com/ACDelcoConnectorsV2/#/catalog

Also check PT 2353.

that might b too wide, but again, I need the mate. I think I might just have to cut the harness, and use the 150 series, then make an 'adapter' to the OEM Crank sensor connector..

[secondchance]

that might b too wide, but again, I need the mate. I think I might just have to cut the harness, and use the 150 series, then make an 'adapter' to the OEM Crank sensor connector..

It's tough to tell sometime looking at the catalog.
Are you looking for the female side? For your custom ignition module?

[-=Jeff=-]

Yes

[secondchance]

Yes

Could this be it?
https://www.aliexpress.com/item/10sets-lot-3-Pin-Way-Metri-Pack-150-Auto-Wire-Connector-Male-Female-Temperature-Sensor-Plug/32810187129.html

[secondchance]

Tough to tell size wise but another one.

https://www.ebay.com/itm/Delphi-Metri-Pack-150-2-Series-3-Way-Male-AND-Female-High-Temp-Silicone-Pigtail/253612407617?epid=1777908147&hash=item3b0c7a3b41:g:oTMAAOSwOrBa8yq0

[WVZR-1]

Guys - very important when shopping connectors GM/Delphi etc ID connectors according to 'terminal' usage NOT the shell. I've never seen 'wire to wire' 150.2 (pull to seat).

The 'male' connector shell spork2367 mentions would do a MP150. I'm not sure that a MP150.2 and a MP150 share dimensions BUT I might doubt.

***Actually Jerry uses a MP150.2 part # but the connector in his image is actually a MP150. The OE is/was a 150.2 pull to seat I'm quite confident.

If you have the 150.2 mating compare it to the dimensions for the 12129615 mentioned.

You can compare using the NEWER APTIV(used to be DELPHI) catalog. I've used the 8A-202 section of GM FSM to create wiring using this catalog for years. This catalog will ID all seals, terminals plugs used with that particular connector/shell.

If the terminals are on 6mm centers on the 150.2 I'd think all is well.

*** terminals on a 150.2 'pull to seat' I believe are 3.5mm spacing so I don't believe a MP150 will do

-=Jeff=- doing 'wire to wire' adapting APTIV can be very useful.

Just enter the 12129615 and GO .....................................

APTIV ....eCAT

https://ecat.aptiv.com

[secondchance]

Guys - very important when shopping connectors GM/Delphi etc ID connectors according to 'terminal' usage NOT the shell. I've never seen 'wire to wire' 150.2 (pull to seat). The 'male' connector shell spork2367 mentions would do a MP150. I'm not sure that a MP150.2 and a MP150 share dimensions BUT I might assume so.

If you have the 150.2 mating compare it to the dimensions for the 12129615 mentioned.

You can compare using the NEWER APTIV(used to be DELPHI) catalog. I've used the 8A-202 section of GM FSM to create wiring using this catalog for years. This catalog will ID all seals, terminals plugs used with that particular connector/shell.

If the terminals are on 6mm centers on the 150.2 I'd think all is well.

-=Jeff=- doing 'wire to wire' adapting APTIV can be very useful.

Just enter the 12129615 and GO .....................................

APTIV ....eCAT

https://ecat.aptiv.com

David,

Good to hear from you! Lacking detailed knowledge, I do what I can - attempt to match visually. I have enough useless connectors in my drawers for sure!

Below is what popped up when I tried 12129615.
https://www.lawsonproducts.com/Metri-Pack/MP-150-Series-3Way-Male-Housing/1446745.lp

[WVZR-1]

David,

Good to hear from you! Lacking detailed knowledge, I do what I can - attempt to match visually. I have enough useless connectors in my drawers for sure!

Below is what popped up when I tried 12129615.
https://www.lawsonproducts.com/Metri-Pack/MP-150-Series-3Way-Male-Housing/1446745.lp


You did something wrong - this direct link should work. Look in documents and related areas when catalog populates. Get out your FSM and experiment using the 8A-202 section.

*** I don't know how long this 'direct link' might remain active.

https://ecat.aptiv.com/feature?search=12129615

[spork2367]

David,

Good to hear from you! Lacking detailed knowledge, I do what I can - attempt to match visually. I have enough useless connectors in my drawers for sure!

Below is what popped up when I tried 12129615.
https://www.lawsonproducts.com/Metri-Pack/MP-150-Series-3Way-Male-Housing/1446745.lp

That is the same one I posted.

I don't believe the series you're looking for is the 150.2, I believe it is the 150. Here is the female I posted the link to next to the mating male which is identical to the connector Jerry lists.

[WVZR-1]

That is the same one I posted.

I don't believe the series you're looking for is the 150.2, I believe it is the 150. Here is the female I posted the link to next to the mating male which is identical to the connector Jerry lists.

I added *** to my comments related to Jerrys Part #. He uses a 150.2 part # but has a MP150 displayed so that should/might answer the 'fit'. I doubt that it would do.

The GM# 12167116 (PT782) is from the GM SPO catalogs. That is 'pull to seat'.

These are from a '95 FSM. I don't believe the earlier years display these in 8A-202

C2 is originally a 150.2 'pull to seat'

9460

9461

It would be difficult/next to impossible to repair a factory harness using a 'pull to seat' shell.

[-=Jeff=-]

Thanks for all the help.. I found it..

Casper Electronics #410016, I ordered a couple, if they work I can eliminate added wiring I put in my car..

[spork2367]

Thanks for all the help.. I found it..

Casper Electronics #410016, I ordered a couple, if they work I can eliminate added wiring I put in my car..

That's interesting. After I dug a little more, Aptiv, formerly delphi, doesn't actually make that connector, they only produce the female version. The male version was always molded into the mating component. Good find.

Here is a pigtailed set:

https://www.ebay.com/itm/Delphi-Metri-Pack-150-2-Series-3-Way-Male-AND-Female-High-Temp-Silicone-Pigtail/253612407617?_trkparms=aid%3D111001%26algo%3DREC.S EED%26ao%3D1%26asc%3D20160908105057%26meid%3D6f8cb 3a913e14ee8a8caefd192a79f4d%26pid%3D100675%26rk%3D 1%26rkt%3D15%26sd%3D253612407617%26itm%3D253612407 617&_trksid=p2481888.c100675.m4236&_trkparms=pageci%3A35d02c14-6848-11e9-9f10-74dbd180e358%7Cparentrq%3A5aadba7816a0ac1f5f45865d fffd81c1%7Ciid%3A1

[-=Jeff=-]

That's interesting. After I dug a little more, Aptiv, formerly delphi, doesn't actually make that connector, they only produce the female version. The male version was always molded into the mating component. Good find.

Here is a pigtailed set:

https://www.ebay.com/itm/Delphi-Metri-Pack-150-2-Series-3-Way-Male-AND-Female-High-Temp-Silicone-Pigtail/253612407617?_trkparms=aid%3D111001%26algo%3DREC.S EED%26ao%3D1%26asc%3D20160908105057%26meid%3D6f8cb 3a913e14ee8a8caefd192a79f4d%26pid%3D100675%26rk%3D 1%26rkt%3D15%26sd%3D253612407617%26itm%3D253612407 617&_trksid=p2481888.c100675.m4236&_trkparms=pageci%3A35d02c14-6848-11e9-9f10-74dbd180e358%7Cparentrq%3A5aadba7816a0ac1f5f45865d fffd81c1%7Ciid%3A1

Nice find.. for my set-up I would rather pin it to my cable, but this is good info

[WVZR-1]

Thanks for all the help.. I found it..

Casper Electronics #410016, I ordered a couple, if they work I can eliminate added wiring I put in my car..

If this does for you what you want it's I'd think the preferred. You know where you can go to get more and they seem to have the specialty terminals required. I'd be interested in seeing the contents in a snapshot. The eBay offering without service terminals etc I'd think NOT a wise buy!

[spork2367]

If this does for you what you want it's I'd think the preferred. You know where you can go to get more and they seem to have the specialty terminals required. I'd be interested in seeing the contents in a snapshot. The eBay offering without service terminals etc I'd think NOT a wise buy!

It’s just an alternative for others who may be looking for one with a pigtail already attached so they don’t have to crimp their own terminals.

[-=Jeff=-]

I wish I would have found these about 6 months ago, either way, in this instance I want to pin them directly, the pigtail can also be useful. If someone made the Wide flat IM mate to connect to the harness that would be even better, but my feeling is that one is only used in our application

[-=Jeff=-]

It fits

9486


Sent from my iPhone using ZR-1 Net Registry (http://r.tapatalk.com/byo?rid=90383)

[WVZR-1]

It fits

9486





What does the other end 'mate' to? You only show what appears to be an empty end with the 'pull to seat' attached on the other end. There had to be a purpose to this!

I was quite sure the 'pull to seat' would be correct.

It just uses the long male terminals with seals etc to wire?

[-=Jeff=-]

Yes uses male terminals and a seal on the end. I wanted to confirm the housing fits before I cut a working wire to connect it there.. There are 3 mate connectors keyed differently this works will all of them and you can use male or female pins. I will get a picture when completed