PDA

View Full Version : Going to dyno this Sunday


ALLTHECAMS
05-24-2018, 10:57 PM
Going on the dyno this Sunday at the same place I dynoed last year. Unfortunately the forcecast says it will be 94 degrees. Hopefully the SAE will compensate.

Last year with Borla Challenge exhaust and a K&N I pulled 350hp/334tq
After OBX headers and a Haibeck chip Im hoping for 370.

ALLTHECAMS
05-29-2018, 08:11 PM
Dyno got postponed. Operater was sick. Have rescheduled for Saturday.

Sent from my XT1710-02 using Tapatalk

ssrszz4
06-02-2018, 02:08 AM
What did you get?

Sent from my XT1585 using ZR-1 Net Registry mobile app (http://r.tapatalk.com/byo?rid=90383)

ALLTHECAMS
06-02-2018, 10:02 AM
Don't know yet. It got rescheduled for 3:00 today.

Sent from my XT1710-02 using Tapatalk

ALLTHECAMS
06-02-2018, 07:32 PM
The results are in!
374hp 362tq!

Sent from my XT1710-02 using Tapatalk

XfireZ51
06-02-2018, 09:14 PM
Please post dyno sheet if possible.

ALLTHECAMS
06-02-2018, 09:22 PM
Please post dyno sheet if possible.Here's a before and after and the two pulls from today75727573

Sent from my XT1710-02 using Tapatalk

jss06c6
06-03-2018, 09:14 AM
Nice.. I guess mine is a dog since it only put down 359 rwhp with SW headers and exhaust and Marc's tune and Fidanza FW.. I've done a lot of refined tuning and gone back to Dual Mass since, but doubt it would be in the 375 range.. runs beautifully, pulls strong, so I'm happy regardless.. not chasing a number.

Sent from my XT1585 using ZR-1 Net Registry mobile app (http://r.tapatalk.com/byo?rid=90383)

ALLTHECAMS
06-03-2018, 10:22 AM
Nice numbers on yours too. It seems my car is a freak. I just wanted to do a before and after on mine to see what I gained.

Sent from my XT1710-02 using Tapatalk

efnfast
06-03-2018, 10:25 AM
ALLTHECAMS, what year is your car?

32valvesftw
06-03-2018, 10:34 AM
His numbers seem similar to mine, I pulled 383 whp with API Intake, Headers, no cats, X-pipe, Borla, and Henderson chip. Ambient temp was about 50F during the dyno. I am not the original owner so I don't know if anything else was done prior to my ownership.

ALLTHECAMS
06-03-2018, 10:37 AM
ALLTHECAMS, what year is your car?It's a 1991

Sent from my XT1710-02 using Tapatalk

jss06c6
06-03-2018, 04:07 PM
Mine is a '91 also. Will be porting plenum and injector housings and port matching heads next. Then re-tune again. Should give me about the same improvement I saw with the headers and tune first go around. Will have my new business set up by second week in September, so will get base curve on our Dyno before swapping to ported top end and re-tuning.

Sent from my XT1585 using ZR-1 Net Registry mobile app (http://r.tapatalk.com/byo?rid=90383)

ssrszz4
06-04-2018, 05:39 PM
Fantastic!!

Sent from my XT1585 using ZR-1 Net Registry mobile app (http://r.tapatalk.com/byo?rid=90383)