PDA

View Full Version : Ported Intake

Locobob
03-11-2015, 09:16 PM
Early style (90-92) ported plenum and injector housings for sale. Plenum ports are 36mm at gasket surface and grow larger upstream, inside of plenum has been extensively worked, corner bolt holes have been sleeved for alignment, throttle bores have been enlarged to accept 63mm throttle body. Injector housings are 36mm through secondary ports, secondary bosses reduced and contoured, primary ports are 36mm halfway down the ports and reduce to 34.5mm at head gasket surface for optimal transition to stock 32mm primary head ports, primary injector bosses have been eliminated.
Easy 25hp bolt on for stock LT-5. Exterior refinishing is recommended, can arrange top end powder coating for extra.
$1500 outright.

http://i418.photobucket.com/albums/pp270/locobob68/For%20Sale/IMG_1271.jpg (http://s418.photobucket.com/user/locobob68/media/For%20Sale/IMG_1271.jpg.html)

http://i418.photobucket.com/albums/pp270/locobob68/For%20Sale/IMG_1273.jpg (http://s418.photobucket.com/user/locobob68/media/For%20Sale/IMG_1273.jpg.html)

http://i418.photobucket.com/albums/pp270/locobob68/For%20Sale/IMG_1276.jpg (http://s418.photobucket.com/user/locobob68/media/For%20Sale/IMG_1276.jpg.html)
Locobob
03-11-2015, 09:17 PM
http://i418.photobucket.com/albums/pp270/locobob68/For%20Sale/IMG_1289.jpg (http://s418.photobucket.com/user/locobob68/media/For%20Sale/IMG_1289.jpg.html)

http://i418.photobucket.com/albums/pp270/locobob68/For%20Sale/IMG_1292.jpg (http://s418.photobucket.com/user/locobob68/media/For%20Sale/IMG_1292.jpg.html)

http://i418.photobucket.com/albums/pp270/locobob68/For%20Sale/IMG_1282.jpg (http://s418.photobucket.com/user/locobob68/media/For%20Sale/IMG_1282.jpg.html)
efnfast
03-12-2015, 07:52 AM
I bought a set of these from Locobob. No issues, and nice bolt on power. Thanks Bob. -Steve
Jagdpanzer
03-12-2015, 08:52 AM
Excellent work Bob!
GOLDCYLON
03-12-2015, 09:10 PM
Any trades for a stock plenum and housing? I'd be interested in the offset cost . Robert
Dynomite
03-13-2015, 12:40 AM
Any trades for a stock plenum and housing? I'd be interested in the offset cost . Robert

I think Robert said......on the "other Forum".......

Yes - forgot to post - $900 + shipping with core return.....

Just in Case Robert is off for the weekend :p
efnfast
03-13-2015, 07:29 AM
Gee, that might even be the core I sent him.
Locobob
03-13-2015, 03:07 PM
Gee, that might even be the core I sent him.

You would be correct Steve... not turning these out as fast as I used to.

Daryl - yeah I'll do $900 with exchange, do you have another Z or something? thought yours was already all done up?
efnfast
03-13-2015, 05:04 PM
If it matters, these came off my 90 with 61K on them. My new ones look most beautiful all powder coated and going down the road much faster.
Vette73
03-13-2015, 06:24 PM
Ok so if you send your stock plenum the cost is 900 plus the shipping?
Just curious....
GOLDCYLON
03-13-2015, 06:38 PM
You would be correct Steve... not turning these out as fast as I used to.

Daryl - yeah I'll do $900 with exchange, do you have another Z or something? thought yours was already all done up?

Yes but I think this is a little hogged out more than mine and I have a 63mm hogged out TB as well. Check ok I'm stuck in LA until next Friday. Not yet but a spare motor. GC
GOLDCYLON
03-13-2015, 06:40 PM
Ok so if you send your stock plenum the cost is 900 plus the shipping?
Just curious....

No it's stock plenum and stock injector housings. That's the trade plus the cash
PhillipsLT5
03-13-2015, 07:33 PM
GC, wheelin & dealin, you go
Vette73
03-13-2015, 07:44 PM
Yes that's what I meant...Ok thanks for getting back...
GOLDCYLON
03-13-2015, 09:07 PM
GC, wheelin & dealin, you go

Always
Locobob
03-14-2015, 01:06 PM
Did I do your intake porting Daryl? Can't remember... anyhow you can give me a call if you want to discuss... because I'm kinda confused about what all you have going on now :D
GOLDCYLON
03-14-2015, 06:00 PM
Did I do your intake porting Daryl? Can't remember... anyhow you can give me a call if you want to discuss... because I'm kinda confused about what all you have going on now :D

Yep you sure did way back in day. Pm me your number bro
GOLDCYLON
03-18-2015, 10:21 AM
After speaking to Bob on Monday im in a hold on this untill I can sort out some measurements. I will pass until then. So as not to hold anybody up. I forgot my heads and injector housings were match ported to the more aggressive 36mm. So these wont suit my purpose until then. And im not good enough with a dremel lol. GC