PDA

View Full Version : Parting out 91 LT5


phrogs
10-19-2011, 11:20 PM
I have a 91 LT5 I am parting out.
This engine is apart I have most parts still but hit me up with what you need and We can see if I have it and see if we can agree on a price.
sold one camshaft need to verify what I have. I believe it was the LH exhaust.
Sold Left RH head
again let me know what you need and we can talk.
jp


quick inventory today

Used parts from a 30K motor that I intended on building but needed money and parted some of it so now its time to finish the job.

2 bolt block with lader $1000
oil pan $300
oil filter housing $300
LH cylinder head $900 drivers side
three camshafts $300 each
air horn $100
throttle body Sold
power steering pump $350
RH chain tensioner with housing compressed $400
LH chain tensioner with housing compressed $400
front engine cover $150
A/C compresor for 91-up $250
brand new secondary vacum pump the one from the truck $200
Coolant tubes $250
Pistons with conecting rods $100 each I have a a bunch
cylinder liners $100 each I have a bunch not from the above block
Spark plug wires MFG by Taylor used $40
spark plug wires LT5 sold
rear crankshaft seal housing $150
fuel pump assembly used $200
AIR parts group $300
Intake accordian Sold
crankshaft is iffy I remember it havind some surface corrosion on it so not sure if it would be worth using to anyone.

NEW PARTS
White Racing products Crankshaft bearing set $650
Camshaft timing chain wear strips or guide facing
I have Two of the cam cover guide facings
and three of the ones for the main chains $350 for all of them

limey
10-19-2011, 11:30 PM
P&A
Ignition module
Ignition module interface board
primary timing chain sprocket

secondchance
10-19-2011, 11:46 PM
ECM?

GOLDCYLON
10-20-2011, 01:19 AM
Plenium and coolant pipes :)

bobbyhi
10-20-2011, 09:56 AM
Plenium and coolant pipes :)


Goldy, I have the coolant pipes off my '90 if you need a set.

Torchred96
10-20-2011, 11:09 AM
Plenum and IH...if Goldcyon passes.

thanks
sam

phrogs
10-20-2011, 08:03 PM
P&A
Ignition module
Ignition module interface board
primary timing chain sprocket


I have one ignition module see them going for a lot of bucks.. one on ebay went for over $800 in the last two weeks.

interface board sold to you I think months ago.

Need to check on the timing chain sproket it might be in the block I need to pull the front cover off Ill let you know asap if I have it.


I do have an interface board but depends on how much you would give me for it since its from my spare motor.

phrogs
10-20-2011, 08:06 PM
Plenium and coolant pipes :)

plenum sold!

See above for coolant tubes.

phrogs
10-20-2011, 08:07 PM
Plenum and IH...if Goldcyon passes.

thanks
sam


Sorry both are sold from this one.

phrogs
10-20-2011, 08:07 PM
ECM?


PM'ed you

GOLDCYLON
10-20-2011, 08:10 PM
plenum sold!

See above for coolant tubes.

Got a pic of the tubes ?

phrogs
10-20-2011, 08:51 PM
http://i150.photobucket.com/albums/s103/zr1salvage/Parts%20Oct%202011/100_0585.jpg
http://i150.photobucket.com/albums/s103/zr1salvage/Parts%20Oct%202011/100_0594.jpg
http://i150.photobucket.com/albums/s103/zr1salvage/Parts%20Oct%202011/100_0597.jpg
http://i150.photobucket.com/albums/s103/zr1salvage/Parts%20Oct%202011/100_0606.jpg
http://i150.photobucket.com/albums/s103/zr1salvage/Parts%20Oct%202011/100_0598.jpg
http://i150.photobucket.com/albums/s103/zr1salvage/Parts%20Oct%202011/100_0603.jpg

phrogs
10-20-2011, 08:52 PM
http://i150.photobucket.com/albums/s103/zr1salvage/Parts%20Oct%202011/100_0602.jpg
http://i150.photobucket.com/albums/s103/zr1salvage/Parts%20Oct%202011/100_0601.jpg
http://i150.photobucket.com/albums/s103/zr1salvage/Parts%20Oct%202011/100_0600.jpg

GOLDCYLON
10-20-2011, 11:14 PM
Found a pair of pipes. I pass thanks

Topfuel
10-26-2011, 01:43 AM
I need a dipstick oil tube have dipstick need the tube THX Mike

SteelBlueZR1
10-26-2011, 06:34 PM
Do you have the air horn black anodized worm gear screw on clamps? If so how much for one?

oricale
10-27-2011, 12:42 PM
Hello there! what do you have interior wise??

thanks!