4L80 auto ZR-1's

[Pete]

Hi All

Looking to see if there is any interest in these.

I will be making 4L80E tail housings to convert any 6 speed C4 into a bullit proof 4L80E trans.

Basicly bolt on the tailhousing to a 4L80E trans use your stock 6 speed C-beam and your stock driveshaft and go racing.

These will sell for $650


Please reply here or PM me.
Opinions welcome.
Pete

[-=Jeff=-]

Hey Pete, you need to post this somewhere for L98/LT1/LT4 guys that want the 4L80e

Might get a bigger amount of interest

[Pete]

Hey Pete, you need to post this somewhere for L98/LT1/LT4 guys that want the 4L80e

Might get a bigger amount of interest


Thanks Jeff

[xlr8nflorida]

Hi All

Looking to see if there is any interest in these.

I will be making 4L80E tail housings to convert any 6 speed C4 into a bullit proof 4L80E trans.

Basicly bolt on the tailhousing to a 4L80E trans use your stock 6 speed C-beam and your stock driveshaft and go racing.

These will sell for $650


Please reply here or PM me.
Opinions welcome.
Pete


:jawdrop:

[QB93Z]

Pete, Interesting project. Do I understand correctly that the $650 does not include the 4L80E transmission?

Jim

[Polo-1]

I buy 12 if $650 inculded the 4L80E too :p

Pete are you looking at just tail housing, right? No need for new output shaft. On the yoke are you cutting down a late model truck or ?

[Pete]

:jawdrop:

If the jaw drop is for the price?

I'm making these here in the USA :flag2:and the above price is cheap had a few other local shops qoute me you don't wanna know,they wanted double the above price each for 10 pieces.

Seems most U.S. companies are hurting and they wanna make up on one costumer.

I'm sure there is somebody out there that will do it for less just a metter of finding them,it's like looking for a needle in a hay stack.:)

China will make this for $10-$20 each for 100 pieces.
Now you know why China is kicking our butt.

Pete

[Pete]

I buy 12 if $650 inculded the 4L80E too :p

Pete are you looking at just tail housing, right? No need for new output shaft. On the yoke are you cutting down a late model truck or ?

Yes, just tail housing.
No need to replace/new output shaft.
No, you use stock yoke/driveshaft and C-beam.

Basicly buy a 4L80E trans install tail housing install in car and reinstall your stock driveshaft and C-beam.

You will also need auto shifter,cable,flexplate (i have),etc.

If you wanted to text your friends while driving the Z, auto is the way to go.:)

Pete

[xlr8nflorida]

The jaw drop was for an auto in a ZR-1. :mrgreen:

I think the price is cheap.

[HADI-ZR1]

Hi Pete.
Give me the design and i will do it here in czech or Kuwait,i think cheaper . and ship it to you.:-D .
1- Can you tell us, what material you gona use?
2- Is this One piece casting product OR multi-welding pieces?
:cheers:
Very nice Idea indeed!!. If i broke my ZF ,maybe i go with Auto!

I made once tail housing for my Supercharged 86 Vette for TH400.

[tccrab]

Pete:

Why re-invent the wheel?
Scroll down to the bottom of the page.
$599 on sale.
http://www.transmissioncenter.net/4L60E_to_4L80E_Swap.htm

TomC
'Crabs

[HADI-ZR1]

Tom, whats your point?

we scroll down, and found the adapter is to convert Auto trany-to Auto.
Not from ZF6 to Auto. :o

[phrogs]

iNTERESTING..

http://www.transmissioncenter.net/HPIM1237_small.JPG



Pete:

Why re-invent the wheel?
Scroll down to the bottom of the page.
$599 on sale.
http://www.transmissioncenter.net/4L60E_to_4L80E_Swap.htm

TomC
'Crabs

[Pete]

If you read carefully you will notice that you have to use the 700r/4L60 output shaft (27 spline) and you are married to that trans what true hod rodder would want a 400/L80 trans with 700r (27 spline) output shaft.
It's doing it halfway.

Also people are breaking the 700r output shafts.

The piece i'm making you don't have to custom build the trans and you keep the HD 400/4L80 (31 spline) output shaft.
Heck even GM knew better to put a big output shaft (31 spline) on all 6 speeds.

So why do it halfway when you can do it the right way.
How many hod rodders build 400 trans and change the output shaft to 27 spline from the stock 31 spline,seems like going backwards.:flag2:


Thanks Guys
Pete

[rkreigh]

when you see what the 480LE costs you won't be worried much about the price for the adapter

I know most folks LOVE the ZF box but when you start drag racing the car alot and trying to hook big power with the IRS, the auto really shines

I converted my TT Z06 to auto (4L65E) and the conversion was 7k

from what I understand the 480LE conversions on the ZR-1 run roughly twice that so it's not exactly a cheap mod

but once you hit it with a modern slush box, all is forgiven on the cost front. really works well, just git and go:-D

[Polo-1]

Yes, just tail housing.
No need to replace/new output shaft.
No, you use stock yoke/driveshaft and C-beam.

Basicly buy a 4L80E trans install tail housing install in car and reinstall your stock driveshaft and C-beam.

You will also need auto shifter,cable,flex plate (i have),etc.

If you wanted to text your friends while driving the Z, auto is the way to go.:)

Pete

Ok So, stay with the smaller 1330 u-joint. Was thinking of going to the 1350.
Who is getting these flex plates made , and are they still SFI approved. Are you looking at the a LS style converter or older LT style? What about the flex plate to pump room Do you know the depth ( do you have to run spacers on the front of the converter to flex plate ? ).

Which controller do you like, I have little use time with the TCI box on a 4L80

As you might notice, I'm think of doing this now that the 402 is in the car....

[tccrab]

If you read carefully you will notice that you have to use the 700r/4L60 output shaft (27 spline) and you are married to that trans what true hod rodder would want a 400/L80 trans with 700r (27 spline) output shaft.
It's doing it halfway.


Sorry Pete, I didn't know about the 27 spline vs. 31 spline.
My last Chebby Auto was a turbo 400.
:icon_scra
It has been a while.....

TomC
'Crabs

[Kb7tif]

Cant wait to see 1/4 mile times.
Well i know the 88 Gta with 225hp would roast the tires like no other, automatic...

[Pete]

Ok So, stay with the smaller 1330 u-joint. Was thinking of going to the 1350.
Who is getting these flex plates made , and are they still SFI approved. Are you looking at the a LS style converter or older LT style? What about the flex plate to pump room Do you know the depth ( do you have to run spacers on the front of the converter to flex plate ? ).

Which controller do you like, I have little use time with the TCI box on a 4L80

As you might notice, I'm think of doing this now that the 402 is in the car....



Kevin,when your ready to do this let me know.
I could save you a few $$$.
TCI is very friendly/easy to use.

Pete

[aafc]

i have installed a 4l60E trans in my zr-1 back in aug. 2004. At the time
i only made about 368 hp to the rear wheels, the 4l60E helded up for a
while. The trouble was when drag racing it took to long to shift from 2nd
to 3rd. So in 2009 i rpl the 4l60E with a 700r4 transmission full manual
shift while SGC did a 368 550 hp pkg witch made 444 rwhp and 418 rwtq
with the 700r4 trans. I raced the car one time before going to BG in apr
2010. it ran an 11.58 @119.70. no more racing till i came back from BG.
well a week later and putting gas in car the trans broke on the way home( 3 miles away). The 700r4-4l60E trans will not hold up to the hp
that i was making.
so i will rpl the the trans with a 4l80E with a tail housing from pete,
and reuse a lot of the parts for the swap.The only thing new will be the 4l80E trans and tail housing.

John Becker
1990 white/black #2546
110k plus miles

[Pete]

Some pictures of the finished product.

[HADI-ZR1]

cool product !! :o
Q: what the Weight differnce between them, if we made the change? :icon_scra
Auto will be less or same?

[Pete]

I never weighed them but i would say the auto will be a bit heavier.
With the 4L80 you'll never have to change the clutch :)

Pete



cool product !! :o
Q: what the Weight differnce between them, if we made the change? :icon_scra
Auto will be less or same?

[FU]

Some pictures of the finished product.

Quality product !!

I never weighed them but i would say the auto will be a bit heavier.
With the 4L80 you'll never have to change the clutch :)

Pete

Won't have to worry about the back end (joint's,half shafts R&P etc.) either , just another plus.

[Aurora40]

That looks really stout!

Just a curiosity question, could a 6L80-E be used? A 6-speed auto Z would be pretty sweet for daily driving.

[Polo-1]

the gearing in the 6L is crap.. It set up for truck. You would need 3.08-2.70 rear end, then you still have a OD thats out of wack..

You made a extra one, right Pete.

[Pete]

I'm pretty sure the the 6L and 4L have same dimensions,will have to ask my trans guys.

Bob,i have one more on hand and more on the way.

Pete




the gearing in the 6L is crap.. It set up for truck. You would need 3.08-2.70 rear end, then you still have a OD thats out of wack..

You made a extra one, right Pete.

[phrogs]

So whats the price tag on this mod?

[HADI-ZR1]

Pete You rebelled against ZF6
:mrgreen:

[FU]

I converted my TT Z06 to auto (4L65E) and the conversion was 7k

from what I understand the 480LE conversions on the ZR-1 run roughly twice that so it's not exactly a cheap mod



14 K is way high. The conversion should cost no more than doing the same in a C5. Parts are the same cost. What say Pete ?

[Pete]

Phrogs the price for just the tail piece is $649.

Frank,your right it's mostly parts and some labor,labor is not all that much

$14k sounds way too high,i would say about half

Majority of money is parts.

Your saving some on driveshaft and C-beam since you'll use your stock ZF pieces no mods needed,that's what so nice about this tailhousing

Pete

[Kenji]

Dear Pete.

I am interested in your project very much.

I expect a report of the progress of the future work.

[HAWAIIZR-1]

Dear Pete.

I am interested in your project very much.

I expect a report of the progress of the future work.

Kenji,

You will be happy in Tokyo traffic with the auto and nice for bracket racing.:dancing


Craig

[Pete]

Dear Pete.

I am interested in your project very much.

I expect a report of the progress of the future work.


Kenji,i have done a few Auto ZR-1's they work fine 2 of them are 10 second cars.

I have the tailhousing to install a 4L80E in any 6 speed C4,also have auto flywheel for LT5.

Let me know what info you need.
You can PM or email petezr1@gmail.com

Pete