PDA

View Full Version : Wills 415 spacers almost done.

rhipsher
11-17-2009, 09:17 AM
I've got to make a few small mods to them but for the most part they're done.

http://i301.photobucket.com/albums/nn63/keeno1970/gasket1.jpg

http://i301.photobucket.com/albums/nn63/keeno1970/gasket2.jpg

http://i301.photobucket.com/albums/nn63/keeno1970/gasket4.jpg

http://i301.photobucket.com/albums/nn63/keeno1970/gasket3.jpg

Our hard working 20 somethings on their 15th smoke break of the day.

http://i301.photobucket.com/albums/nn63/keeno1970/hardworkers.jpg
tomtom72
11-17-2009, 10:19 AM
Smoke less....more working time.

Rick, those are nice!:thumbsup:

A dumb Q....the need for those would be to clear a dropped plenum floor? Sorry, don't mean to be asking about other people's speed secrets....:redface:
limey
11-17-2009, 10:24 AM
Blimey,

I could have hooked you up here & saved you a whole bunch of headaches, built them with or without nozzles. Clearance with the hood & allowing fitment for the nozzles was the biggest challenge for us.



http://www.whiteracingproducts.com/images1/NOS/DSC00188.JPG


http://www.whiteracingproducts.com/images1/NOS/DSC00192.JPG


http://www.whiteracingproducts.com/images1/NOS/DSC00384.JPG


http://www.whiteracingproducts.com/images1/NOS/DSC00385.JPG


http://www.whiteracingproducts.com/images1/NOS/DSC00389.JPG
rhipsher
11-17-2009, 10:52 AM
The reason Will needed them was because he had someone machine the faces of his plenum and IH housings and they took to much meterial off so his plenum was sitting on his A/C compressor. He tried to grind a little off to make it clear but that wasn't enough. They only take 3 1/2 minutes a piece to machine. But of course programming and set up time takes much longer.
mgbrv8
11-17-2009, 01:41 PM
Beautiful work guys. The bed way of you CNC looks like a Haas.

Dave
rhipsher
11-17-2009, 02:03 PM
Beautiful work guys. The bed way of you CNC looks like a Haas.

Dave

Its a big 50 taper machine. A Puma 5025. There were two other jobs set up on that mill table. I just found an empty spot toward the back of the table and set the spacers up right there. The only thing that sucked was I had to lean way over one of the other jobs to reach the spacers and my shirt was getting soaked with coolant.
jonszr1
11-17-2009, 06:37 PM
rick awsome work and you built them to his specks . instead of just buying something off the shelf .that way he was sure everything would fit just right .:thumbsup:
Paul Workman
11-17-2009, 06:46 PM
Blimey,

I could have hooked you up here & saved you a whole bunch of headaches, built them with or without nozzles. Clearance with the hood & allowing fitment for the nozzles was the biggest challenge for us.



http://www.whiteracingproducts.com/images1/NOS/DSC00188.JPG


http://www.whiteracingproducts.com/images1/NOS/DSC00192.JPG


http://www.whiteracingproducts.com/images1/NOS/DSC00384.JPG


http://www.whiteracingproducts.com/images1/NOS/DSC00385.JPG


http://www.whiteracingproducts.com/images1/NOS/DSC00389.JPG

WOW! That looks wicked!!:thumbsup:
USAFPILOT
11-17-2009, 06:55 PM
that NOS setup is cool! Nice job on those spacers Rick.
rhipsher
11-17-2009, 09:04 PM
rick awsome work and you built them to his specks . instead of just buying something off the shelf .that way he was sure everything would fit just right .:thumbsup:And I didn't charge him a dime for them. Just a favor for a friend. I don't think anybody will be able to beat that price.:mrgreen:
Polo-1
11-17-2009, 09:36 PM
Hey Friend :mrgreen:

My Mono runner is in the middle of it's work. Getting fixed is more like it,to make it flat and seal again. I might run into the same problem, can I work something out with you if needed.

http://i7.photobucket.com/albums/y292/kpie/KevinPietro001.jpg
LGAFF
11-17-2009, 09:45 PM
http://i7.photobucket.com/albums/y292/kpie/KevinPietro001.jpg

Wow those have some serious flow.
rhipsher
11-17-2009, 10:56 PM
Hey Friend :mrgreen:

My Mono runner is in the middle of it's work. Getting fixed is more like it,to make it flat and seal again. I might run into the same problem, can I work something out with you if needed.

http://i7.photobucket.com/albums/y292/kpie/KevinPietro001.jpgSure. Of course I can't do everything for free. I definitely like to get paid for moonlighting. But Will is a good friend plus I figured he might let me take his 415 for a spin.:mrgreen: Just kidding.
Polo-1
11-18-2009, 12:01 AM
would not expect it for free, just knowing you have a set or can cut out a extra set if needed.

:thumbsup:
rhipsher
11-18-2009, 08:58 AM
would not expect it for free, just knowing you have a set or can cut out a extra set if needed.

:thumbsup:Just let me know if you need them.
W i l l
11-18-2009, 02:35 PM
Rick,

The spacer plates look AWESOME. What a work of art!!

Will

I've got to make a few small mods to them but for the most part they're done.

http://i301.photobucket.com/albums/nn63/keeno1970/gasket1.jpg

http://i301.photobucket.com/albums/nn63/keeno1970/gasket2.jpg

http://i301.photobucket.com/albums/nn63/keeno1970/gasket4.jpg

http://i301.photobucket.com/albums/nn63/keeno1970/gasket3.jpg

Our hard working 20 somethings on their 15th smoke break of the day.

http://i301.photobucket.com/albums/nn63/keeno1970/hardworkers.jpg
jonszr1
11-18-2009, 06:52 PM
rick , you gotta e mail me after you get a ride in that bad boy ,shoot when the nitros button is hit you might just have a time machine :thumbsup: